Purpose: to activate Lane Assist for vehicles with Sign Assist and/or Light Assist options.
Vehicle must be equipped with camera Ref 5Q0, example: 5Q0-980-653-E (Octavia phase 1)
Warning!! There are 12 programming steps to complete here.
After programming, the error ” Steering C10AC F2 – Lane Keeping Assist interface not programmed ” may appear in A5. Clear the error, restart the MIB, then turn off the ignition and lock the vehicle for more than 2 minutes. Lane Assist should then function normally.
Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.
2 – Switch on the ignition and run the VCDS program.
Line 1:
3 – Click on“Select”, then click on“17 – Instruments“.
4 – Click on“Coding – 07” then click on“Long Coding Helper“.
5 – Select byte“4”
Then check Bit“6”:“Lane Maintenance Assist installed”.
Line 2:
3 – Click on“Select”, then click on“17 – Instruments“.
4 – Click on ” Coding – 07” then click on“Long Coding Helper“.
5 – Select byte “11“
. Then check bit “1“: “Lane Maintenance Assist information (BAP) installed/active“
Line 3:
3 – Click “Select,” then click “A5 – Frt Sens. Drv. Assist.“
4 – Click on ” Coding – 07,” then click on “Long Coding Helper“
5 – Select the “0” byte
Then, in the “Bit 0-7” drop-down menu, select “01 Coding_HCA coded.”
Line 4:
3 – Click “Select,” then click “A5 – Frt Sens. Drv. Assist.“
4 – Click “Security Access – 16,” then enter the code “20103“
5 – Click “Adaptation – 10.”
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “HCA_On_State“
7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “Menu” and then confirm.
Line 5:
3 – Click “Select,” then click “A5 – Frt Sens. Drv. Assist.“
4 – Click “Security Access – 16,” then enter the code “20103“
5 – Click “Adaptation – 10.”
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “HCA_Warning_intensity“
7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “Menu” and then confirm.
Line 6:
3 – Click “Select,” then click “A5 – Frt Sens. Drv. Assist.”
4 – Click “Security Access – 16,” then enter the code “20103“
5 – Click ” Adaptation – 10.”
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “BAP_Personalisierung.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “not activated” and then confirm.
Line 7:
3 – Click “Select,” then click “A5 – Frt Sens. Drv. Assist.“
4 – Click on “Security Access – 16,” then enter the code “20103“
5 – Click on ” Adaptation – 10.”
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Customization of Lane Departure Warning Class 15 and above“
7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “last setting” and then confirm.
Line 8:
3 – Click “Select,” then click “44 – Steering Assist.”
4 – Click on “Security Access – 16,” then enter the code “19249“
5 – Click on ” Coding – 07,” then click on “Long Coding Helper“
6 – Select byte “0“
Then check bit “4“: “Lane Assist installed“
Line 9:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6- On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-LDW_HCA_0x19”.
7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“activated” and confirm.
Line 10:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6- On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-LDW_HCA_0x19_msg_bus”.
7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.
Line 11:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle menu operation menu_display_Lane_Departure_Warning”.
7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.
Line 12:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle menu operation menu_display_Lane_Departure_Warning_over_threshold_high”.
7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.
This post is also available in:
Français (French)
