Audi Q3 F3 (FS) (2018+ ) / Audi SQ3 / RSQ3
Q3 (F3) – Activate a second Bluetooth phone
Purpose: Allows you to connect two phones simultaneously via Bluetooth to the MMI if you don't have the Audi Phone Box option....
Q3 (F3) – Activate daytime running lights (DRL) only in Auto position
Purpose: Enables daytime running lights (DRL) only when the headlight control switch is in the "auto" position. Proceed : 1 - Engine...
Q3 (F3) – Activate G-Meter
Purpose: Adds the G-Meter (Accelerometer) to the Virtual Cockpit screen. Proceed : 1 - Engine off, ignition off, connect your official VAG-COM...
Q3 (F3) – Activate intruder alarm with horn
Purpose: to activate an alarm with horn in the event of intrusion into the vehicle, and to lock the vehicle if the...
Q3 (F3) – Activate Lane Assist memory function
Purpose: to store the Lane Assist function in memory. If you deactivate it, the Lane Assist will not automatically resume the next...
Q3 (F3) – Activate rearview camera (retrofit)
Purpose: Enables the rearview camera after it has been installed on the MMI (Low or High camera retrofit). Procedure: 1 - With...
Q3 (F3) – Activate RS Monitor on MMI
Purpose: to activate the RS Monitor on the MMI (MIB2+ MH2P or MIB3). The RS monitor replaces the “Vehicle details” tab, but...
Q3 (F3) – Activate trailer hitch (retrofit)
Purpose: Enables the installation of a retrofit trailer hitch (trailer/towbar retrofit). Caution! The configuration in the control unit for motor 01 is...
Q3 (F3) – Activate window operation with ignition off
Purpose: Enables the windows to be operated (up/down) with the ignition off and the door open. Proceed : 1 - Engine off,...
Q3 (F3) – Activate/deactivate daytime running lights (DRL) via MMI
Purpose: to activate/deactivate the daytime running lights (DRL) via the MMI in the CAR menu. ATTENTION to your country's regulations and technical...
Q3 (F3) – Activation of progressive interior lighting
Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights are switched on and off...
Q3 (F3) – Adjust Soundaktor volume
Purpose: to adjust/deactivate the volume of the Soundaktor (speaker built into the windscreen bay to simulate a false engine noise). If you...
Q3 (F3) – Automatic door unlocking with DSG in “P” position
Purpose: Automatically unlocks all doors when the DSG automatic transmission is shifted to the "P" position. Procedure: 1 - Engine off, ignition...
Q3 (F3) – Comfort flashing light
Purpose: to set the number of flashes for the “Comfort flashing” option. Proceed : 1 - Engine off, ignition off, connect your...
Q3 (F3) – Daytime running light deactivation (DRL) using the handbrake
Purpose: to deactivate the daytime running lights (DRL) using the handbrake. Proceed : 1 - Engine off, ignition off, connect your official...
Q3 (F3) – Deactivate “Switch on low beam” message
Purpose: Disables the warning message or dialog prompting the driver to turn on the low beams when the headlight switch is in...
Q3 (F3) – Deactivate open door alarm with contact
Purpose: to deactivate the alarm which is triggered when the door is opened and the contact is in position P. Procedure: 1...
Q3 (F3) – Deactivate right-hand overtaking prevention
Purpose: to deactivate the ACC lane assist system, e.g. when on the freeway and there is a traffic jam in the left...
Q3 (F3) – Deactivate roller blind when locking/unlocking
Purpose: Allows you to disable the roller shade's comfort mode when locking or unlocking. Procedure: 1 - Engine off, ignition off, connect...
Q3 (F3) – Deactivate/activate electric handbrake for rear brake pad change
Purpose: to deactivate/activate the electric handbrake in maintenance mode in order to change/replace the rear brake pad/disc linings. (Lining change mode) Proceed...
Q3 (F3) – Delete belt alarm
Purpose: to suppress the audible alarm and warning light in the Virtual Cockpit when driving without a seatbelt. Proceed : 1 -...
Q3 (F3) – Disable AM frequency on the MMI
Purpose: to deactivate the AM radio frequency on the MMI (AM radio frequency is rarely used, unlike FM radio frequency). Procedure: 1...
Q3 (F3) – Disable the SAFELOCK feature
Purpose: Allows you to disable the SafeLock feature, displaying the warning message "Check SAFELOCK! Owner's manual!" on the ODB after the ignition...
Q3 (F3) – Door lock/unlock confirmation (beep/horn)
Purpose: to set confirmation of door locking/unlocking with beep (alarm) or horn. Warning!! There are 5 lines of code to write here—actually,...
Q3 (F3) – Electronic differential lock (XDS)
Purpose: to set the electronic differential lock (XDS) The Electronic Differential Lock (XDS) is an extension of the familiar EDS function.XDS does...
Q3 (F3) – Flash mode lights during emergency braking
Purpose: Enables the turn signals to flash during an emergency stop. Proceed : 1 - Engine off, ignition off, connect your official...
Q3 (F3) – High Beam Assist activation
Purpose: activates High Beam Assist for vehicles with Sign Assist and/or Lane Assist options. The vehicle must be equipped with the 3Q0...
Q3 (F3) – High Beam Assist always active
Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off. Proceed : 1...
Q3 (F3) – Hill Start Assist
Purpose: to set Hill Start Assist operation. (hill-start assist) Proceed : 1 - Engine off, ignition off, connect your official VAG-COM VCDS...
Q3 (F3) – Increase gas pedal sensitivity
Purpose: to increase accelerator pedal sensitivity. (better acceleration response with S Tronic, more significant than with manual). Proceed : 1 - Engine...
Q3 (F3) – Key operation with ignition on
Purpose: Allows you to use the key and lock the vehicle with the ignition switched on or the engine running. (Very practical...
Q3 (F3) – Lane Assist activation
Purpose: to activate Lane Assist for vehicles with Sign Assist and/or Light Assist options. The vehicle must be equipped with a 3Q0...
Q3 (F3) – Lane Assist settings
Purpose: Adjusts lane departure warning, driver inactivity deactivation threshold, steering assist intensity and steering wheel vibration intensity. Procedure: 1 - Engine off,...
Q3 (F3) – Lap Timer
Purpose: to add the stopwatch to the Virtual Cockpit. Proceed : 1 - Engine off, ignition off, connect your official VAG-COM VCDS...
Q3 (F3) – Lower passenger mirror when reversing
Purpose: Automatically lowers the passenger-side rearview mirror when reversing. Le bouton de réglage des rétroviseurs doit être en position "R", pour que...
Q3 (F3) – Microphone sensitivity adjustment
Purpose: to adjust the intensity of the hands-free system's microphone. Proceed : 1 - Engine off, ignition off, connect your official VAG-COM...
Q3 (F3) – Mirror folding adjustment with remote control
Purpose: Allows you to set the option to fold the side mirrors using the remote control when locking the vehicle. The vehicle...
Q3 (F3) – Needle check
Purpose: to activate the scanning of the speedometer needles when the car is started. (Works with Virtual Cockpit) (Needle Sweep) Proceed :1...
Q3 (F3) – Oil temperature on Virtual Cockpit
Purpose: displays oil temperature in Virtual Cockpit. Proceed : 1 - Engine off, ignition off, connect your official VAG-COM VCDS cable to...
Q3 (F3) – Panel display on Virtual Cockpit
Purpose: displays speed limit signs in Virtual Cockpit (Sign Assist) Vehicle must be equipped with 3Q0 camera (until 2020)Warning! There are 9...
Q3 (F3) – Rear lights activated with daytime running lights (DRL)
Purpose: Enables the rear lights to turn on when the daytime running lights (Scandinavian DRL) are activated (This method turns on the...
Q3 (F3) – Refuel quantity display on Virtual Cockpit
Purpose: Displays the amount of fuel needed to completely fill your tank in Virtual Cockpit. Proceed : 1 - Engine off, ignition...
Q3 (F3) – Reprogramming a new battery
Purpose: Allows you to reprogram or recode all data for the new battery after it has been replaced. Watch out! There are...
Q3 (F3) – Speed of radar (or reversing camera) deactivation
Purpose: Selects the speed at which the radar and/or reversing camera are deactivated. Proceed : 1 - Engine off, ignition off, connect...
Q3 (F3) – Start/Stop deactivation
Purpose: to disable Start and Stop completely. Watch out! There are 1 or 2 lines of coding to do here, depending on...
Q3 (F3) – Suppress electric tailgate beeps
Purpose: to deactivate beeps when opening/closing the trunk/electric liftgate. Proceed : 1 - Engine off, ignition off, connect your official VAG-COM VCDS...
Q3 (F3) – Third brake light on if trunk is open
Purpose: to keep the 3rd brake light on if the trunk is not fully closed. For security lighting at night or to...
Q3 (F3) – Trunk-open license plate illumination
Purpose: turns on license plate illumination when trunk / tailgate is open. Warning! There are 3 lines of coding to do here....
Q3 (F3) – Wireless CarPlay activation
Purpose: Enables Apple CarPlay Wireless and Google Android Auto Wireless to be activated without the need for a USB cable. The vehicle...
This post is also available in:
Français (French)
