Purpose: When the lock or unlock button on the key fob is pressed, this feature causes the daytime running lights and taillights on a vehicle equipped with LED headlights featuring Dynamic Light Assist and LED taillights to turn on in addition to the single or double turn signals.
Warning!! There are 11 lines of code to write here. Save your original coding.
Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.
2 – Switch on the ignition and run the VCDS program.
Line 1:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte2SL VLB10-Dimming”.
7 – Activate the function: “Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” by activating the following 2 lines:
Line 2:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Dyn. turn signal modes-ZV_Blinken_zu “
7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.
Line 3:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Dyn. turn signal modes-ZV_Blinken_auf “
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Active” and then confirm.
For daytime running lights :
Line 4:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte2SL VLB10- Lichtfunktion B 2”.
7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
On this, select“Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” then confirm.
Line 5:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte3SL VRB21- Lichtfunktion B 3”.
7 – On the same page is a second drop-down menu, but at the bottom
of the page.
On the latter, select“Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” then confirm.
Line 6:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte4TFL LB4- Lichtfunktion B 4”.
7 – On the same page is a second drop-down menu, but at the bottom
of the page.
On the latter, select“Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” then confirm.
Line 7:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte5TFL RB32- Lichtfunktion B 5”.
7 – On the same page is a second drop-down menu, but at the bottom
of the page.
On the latter, select“Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” then confirm.
For interior taillights:
Line 8:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte27NSL RC6- Lichtfunktion D 27”.
7 – On the same page is a second drop-down menu, but at the bottom
of the page.
On the latter, select“Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” then confirm.
Line 9:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte27NSL RC6- Dimmwert CD 27”.
7 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“100” and confirm.
For the exterior taillights:
Line 10:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte20BR LA71-Lichtfunktion B 20”.
7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
On this, select“Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” then confirm.
Line 11:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte21BR RC8-Lichtfunktion B 21”.
7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
On this, select“Aktive Blinkfuntion hat ein auf 1 gesetztes zugeordnetes Bit in pa_dynamisch blinken” then confirm.
This post is also available in:
Français (French)
