Purpose: Enables the rear turn signals and LED taillights to flash out of phase.
Warning!! There are 24 lines of code to write here. Save your original coding (Leon Phase 1 only)
Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.
2 – Switch on the ignition and run the VCDS program.
Line 1:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte23SL HLC10-Lichtfunktion E 23.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “Blinken Links Dunkelphase” and then confirm.
Line 2:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on “Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte23SL HLC10-Dimmwert EF 23.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
Set the value to “100” and then confirm.
Line 3:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte23SL HLC10-Dimming Direction EF 23.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “maximize” and click “OK.”
Line 4:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte23SL HLC10-Lichtfunktion G 23.”
7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select “Blinken links Hellphase” and then confirm.
Line 5:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte23SL HLC10-Dimmwert GH 23.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
Set the value to “0” and then confirm.
Line 6:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte23SL HLC10-Dimming Direction GH 23.”
7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select “minimize” and then confirm.
Line 7:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte24SL HRA65-Lichtfunktion E 24.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Blinken rechts Dunkelphase” and then confirm.
Line 8:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte24SL HRA65-Dimmwert EF 24.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
Set the value to “100” and then confirm.
Line 9:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – Sur cette page, tout en haut, il y a un menu déroulant.
Dans ce menu déroulant, choisir « Leuchte24SL HRA65-Dimming Direction EF 24 »
7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “maximize“ and then confirm.
Line 10:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte24SL HRA65-Lichtfunktion G 24.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Blinken rechts Hellphase” and then confirm.
Line 11:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte24SL HRA65-Dimmwert GH 24.”
7 – On this same page, there is a second drop-down menu, but it’s located toward the bottom
of the page.
Set the value to “0” and then confirm.
Line 12:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte24SL HRA65-Dimming Direction GH 24.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “minimize“ and then confirm.
Line 13:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte26NSL LA72-Lichtfunktion E 26.”
7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select “Blinken links Dunkelphase” and then confirm.
Line 14:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte26NSL LA72-Dimmwert EF 26.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
Set the value to “100” and then confirm.
Line 15:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte26NSL LA72-Dimming Direction EF 26.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “maximize” and click “OK.”
Line 16:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte26NSL LA72-Lichtfunktion G 26.”
7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select “Blinken links Hellphase” and then confirm.
Line 17:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte26NSL LA72-Dimmwert GH 26.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
Set the value to “0” and then confirm.
Line 18:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte26NSL LA72-Dimming Direction GH 26.”
7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select “minimize” and then confirm.
Line 19:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte27NSL RC6-Lichtfunktion E 27.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Blinken rechts Dunkelphase” and then confirm.
Line 20:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte27NSL RC6-Dimmwert EF 27.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
Set the value to “100” and then confirm.
Line 21:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte27NSL RC6-Dimming Direction EF 27.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “maximize” and click “OK.”
Line 22:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte27NSL RC6-Lichtfunktion G 27.”
7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Blinken rechts Hellphase” and then confirm.
Line 23:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte27NSL RC6-Dimmwert GH 27.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
Set the value to “0” and then confirm.
Line 24:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Leuchte27NSL RC6-Dimming Direction GH 27.”
7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “minimize“ and then confirm.
This post is also available in:
Français (French)
