Purpose: Allows changeover between normal daytime running lights and normal daytime running lights with US daytime running lights in light switch position “0”. For position and low-beam lights, you need to decide on a coding version. (save your original coding for a return to the original, does not work on all models)
Watch out! There are 27 lines of coding to be seen here, 29.
Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.
2 – Switch on the ignition and run the VCDS program.
Line 1:
3 – Click on“Select”, then click on“09 – Cent. Elect.”.
4 – Click on“Security Access – 16” then enter the code“31347”.
5 – Click on“Adaptation – 10”.
6 – Modify channels :
Channel “daytime running light / daytime running light activation by BAP or operating sequence possible” set value to “active”.
Channel “light 0 BLK VL B36 light function A 0” set value to “active 100%”
Channel “light 0 BLK VL B36 -Dimming value AB 0” set value to “0”.
Channel “light 0 BLK VL B36 light function C 0” set value to “daytime running light”
Channel “light 0 BLK VL B36 dimming value CD 0” set percentage value as desired
Channel “Luminaire 0 BLK VL B36-Dimming Direction CD 0” Set value to “maximize”.
Channel “Luminaire 0 BLK VL B36 light function F 0” Set value to “Flashing left light phase”.
Channel “Luminaire 0 BLK VL B36 dimming value EF 0” set value to “100”.
Channel “Luminaire 0 BLK VL B36-Dimming Direction EF 0” Set value to “minimize”.
Channel “Luminaire 0 BLK VL B36 light function H 0” Set value to “Flashing left dark phase”.
Channel “Luminaire 0 BLK VL B36 -Dimming value GH 0” set value to “0”.
Channel “lamp 0 BLK VL B36-Dimming Direction GH 0” set value to “minimize”
Channel “lamp1BLK VRB20 light function A 1” set value to “active 100%”
Channel “lamp1BLK VRB20 dimming value AB 1” set value to “0”
Channel “lamp1BLK VRB20 light function C 1” set value to “daytime running light”
Channel “lamp1BLK VRB20 dimming value CD 1” set percentage value as desired
Channel “Luminaire1BLK VRB20-Dimming Direction CD 10” set value to “minimize”
Channel “luminaire1BLK VRB20 light function F 1” set value to “flashing right light phase”.
Channel “luminaire1BLK VRB20 dimming value EF 1” set value to “100”
Channel “Luminaire1BLK VRB20-Dimming Direction EF 1” Set value to “minimize”.
Channel “Luminaire1BLK VRB20 light function H 1” Set value to “Flashing right dark phase”.
Channel “Luminaire1BLK VRB20 dimming value GH 1” Value set to “0”
Channel “lamp1BLK VRB20-Dimming Direction GH 1” set value to “minimize”
Channel “lamp2SL VLB10 light function A 2” change value from “daytime running light” to “active 100%”
Channel “Light3SL VRB21 light function A 3” Change value from “Daytime running light” to “Active 100%”
Channel “Light4TFL LB4 light function A 4” Change value from “Daytime running light” to “Terminal 15 with overrun until vehicle comes to a standstill”
Channel “Light5 TFL RB32 light function A 5” Change value from “daytime running lights” to “Terminal 15 with overrun until vehicle comes to a standstill”
And if desired (then US lighting is on for position / low beam, otherwise always off)
Channel “Light 0 BLK VL B36 light function D 0” Set value to “General parking light (tail light; position light; parking light)”
Channel “Light1BLK VRB20 light function D 1” Set value to “General parking light (rear light; position light; parking light )”