Purpose: displays speed limit signs on the ODB/Virtual Cockpit (Sign Assist)
The vehicle must be equipped with a 3Q0 camera (the camera is located at the top of the windshield, level with the rearview mirror, in the shape of a triangle).
Warning! There are 9 lines of coding to do here.
Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.
2 – Switch on the ignition and run the VCDS program.
Line 1:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21”.
7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.
Line 2:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus”.
7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.
Line 3:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification”.
7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.
Line 4:
3 – Click on“Select” then click on“5F – Electr. information”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high”.
7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.
Line 5:
3 – Click on“Select” then click on “.5F – Information Electr.”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Coding – 07” then click on“Long Coding Helper”.
6 – Select byte“24”
Select Bit 6
Line 6:
3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist “.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Coding – 07” then click on“Long Coding Helper”.
6 – Select byte“16”
Then, in the Bit 4 drop-down menu, select“Traffic sign recognition (VZE) active [PR-QR9]”.
Line 7 (Optional):
3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist “.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.
7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.
Line 8:
3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist “.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Adaptation – 10”.
6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Road Sign Detection Fusion Mode” /“Détection des panneaux de signalisation mode fusion”.
7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Traffic sign detection” to use camera recognition only, or“Traffic sign fusion” for camera + gps speed, then confirm.
Line 9:
3 – Click on“Select”, then click on“17 – Instruments”.
4 – Click on“Security Access – 16” then enter the code“20103”.
5 – Click on“Coding – 07” then click on“Long Coding Helper”.
6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.
