Purpose: to change the language of the MMI Bluetooth module’s Voice Command.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


Line 1:

3 – Click on“Select”, then click on“77 – Telephone“.

4 – Click on “Coding – 07“.

5 – Replace the 6th digit of the coding string with the language of your choice:

00x0x00 = Voice Control Off
00x0x10 = German
00x0x20 = English (UK)
00x0x30 = French
00x0x40 = Italian
00x0x50 = Spanish
00x0x60 = Spanish (USA)
00x0x70 = English (USA)
00x0x80 = French (Canada)
00x0x90 = Speaker dependant voice selection

L’article A6 (C6) – Change Voice Command language est apparu en premier sur VAG Coding.

Purpose: activates ambient lighting and menu on MMI (after wiring and lighting of floor stand and/or door for retrofitting).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Coding for the MMI ambient lighting menu :

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle function list BAP-interieur_light_0x08“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle menu operation-menu_display_ambient_illumination“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle menu operation-menu_display_ambient_illumination_over_threshold_high“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart MMI

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior light, light configuration- Ambiente_Applikationsleisten_in_Tuertafel“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Installed” and confirm.

Line 5:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interior light, light configuration- Ambiente_Lautsprecher“

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Installed” and confirm.

Line 6:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interior light, light configuration- Fussraumbeleuchtung“

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Installed” and confirm.

Coding for foot/floor light :

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Int. light, 2nd generation : Defaultwert Ambienteprofil Fussraum“

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select”100″ and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte30FR LC72 – Lichtfunktion A 30“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Footwell Light” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte30FR LC72 – Dimmwert AB 30“.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select”100″ and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 5

Set bit 7 “Footwell Lights Installed

Coding for Door Light :

Line 1:

3 – Click on“Select” then click on“42-Driver door“.

4 – Click on“Coding – 07“.

5 – Select byte 01 and check bit 1 “Ambient Lighting installed”.

Line 2:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07“.

5 – Select byte 01 and check bit 1 “Ambient Lighting installed”.

L’article A3 (8V) – Activate ambient lighting est apparu en premier sur VAG Coding.

Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “Terminal 15“

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article A7 (C7) – Activate reversing camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “Terminal 15“

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article A6 (C7) – Activate reversing camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 5 = video line
Pin 11 = shielding

L’article Q3 (8U) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 5 = video line
Pin 11 = shielding

L’article A1 (8X) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to adjust Bluetooth microphone sensitivity with Audi MMI 3G.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3G Hidden Menu

Press CAR + SETUP for 6 sec to bring up the hidden menu.

main > diagnostics > settings > Mic sensiblity

Choose a value between : -6db/0db/+6db

Restart MMI

Simultaneously press SETUP (1) + Central knob (2) + Top right knob (3)

L’article Q5 (8R) – Microphone sensitivity adjustment est apparu en premier sur VAG Coding.

Purpose: to adjust Bluetooth microphone sensitivity with Audi MMI.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

For MMI 2G :

3 – Click on“Select”, then click on“77 – Telephone”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose Channel 131 or 07.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose a value expressed in“dB” (default value“0 dB”) then validate.

For MMI 3G :

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3G Hidden Menu

Press CAR + SETUP for 6 sec to bring up the hidden menu.

main > diagnostics > settings > Mic sensiblity

Choose a value between : -6db/0db/+6db

Restart MMI

Simultaneously press SETUP (1) + Central knob (2) + Top right knob (3)

L’article A5 (8T) – Microphone sensitivity adjustment est apparu en premier sur VAG Coding.

Purpose: to adjust Bluetooth microphone sensitivity with Audi MMI.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

For MMI 2G :

3 – Click on“Select”, then click on“77 – Telephone”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose Channel 131 or 07.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose a value expressed in“dB” (default value“0 dB”) then validate.

For MMI 3G :

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3G Hidden Menu

Press CAR + SETUP for 6 sec to bring up the hidden menu.

main > diagnostics > settings > Mic sensiblity

Choose a value between : -6db/0db/+6db

Restart MMI

Simultaneously press SETUP (1) + Central knob (2) + Top right knob (3)

L’article A4 (B8) – Microphone sensitivity adjustment est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the Trip Computer/Virtual Cockpit.

Note: these changes affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel: “Display correction of consumptions and operating range”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96.

Example 3: the consumption announced by the ODB is 5.9l/100km, after checking it is actually 6.3l/100km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%, and the consumption announced by the ODB will be a pessimistic 0.1l/100km.

Consumption is immediately modified on the MMI.

L’article Q7 (4M) – Correction of ODB consumption display est apparu en premier sur VAG Coding.