Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off.

SFD: yes


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“High Beam Assistance – Fernlichtassistent Reset“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“not active” and confirm.

L’article Born (K11) – Light Assist always active est apparu en premier sur VAG Coding.

Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off.

SFD: yes


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“High Beam Assistance – Fernlichtassistent Reset“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“not active” and confirm.

L’article Enyaq (NY) – Light Assist always active est apparu en premier sur VAG Coding.

Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off.

SFD: yes


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“High Beam Assistance – Fernlichtassistent Reset“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“not active” and confirm.

L’article ID.4 (E2) – Light Assist always active est apparu en premier sur VAG Coding.

Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off.

SFD: yes


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“High Beam Assistance – Fernlichtassistent Reset“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“not active” and confirm.

L’article ID.3 (E1) – Light Assist always active est apparu en premier sur VAG Coding.

Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Assistance light functions-Fernlichtassistent Reset”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“not active” and confirm.

L’article Ibiza (6F) – Light Assist always active est apparu en premier sur VAG Coding.

Purpose: to set the speed thresholds for activation/deactivation of the high beam assistant (light assist).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Adjust high beam assistant activation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel :“ High beamvariation speed” or “Aktivierungsgeschwindigkeitfür Fernlichtassistent”.

Adjust value accordingly
Default: 57 km/h

Adjusting the high beam assistant deactivation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel : “Headlight dimming speed” or “Geschwindigkeitsschwelle für Fernlichtempfehlung”.

Adjust value accordingly
Default: 27 km/h

L’article Q5 (8R) – High beam assistant settings est apparu en premier sur VAG Coding.

Purpose: to set the speed thresholds for activation/deactivation of the high beam assistant (light assist).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Adjust high beam assistant activation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel :“ High beamvariation speed” or “Aktivierungsgeschwindigkeitfür Fernlichtassistent”.

Adjust value accordingly
Default: 57 km/h

Adjusting the high beam assistant deactivation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel : “Headlight dimming speed” or “Geschwindigkeitsschwelle für Fernlichtempfehlung”.

Adjust value accordingly
Default: 27 km/h

L’article A5 (8T) – High beam assistant settings est apparu en premier sur VAG Coding.

Purpose: to set the speed thresholds for activation/deactivation of the high beam assistant (light assist).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Adjust high beam assistant activation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel :“ High beamvariation speed” or “Aktivierungsgeschwindigkeitfür Fernlichtassistent”.

Adjust value accordingly
Default: 57 km/h

Adjusting the high beam assistant deactivation speed threshold :

3 – Click on ” Select”, then click on “Select”.20 – High beam wizard” .

4 – Click on “Adaptation – 10”.

5 – Select Channel : “Headlight dimming speed” or “Geschwindigkeitsschwelle für Fernlichtempfehlung”.

Adjust value accordingly
Default: 27 km/h

L’article A4 (B8) – High beam assistant settings est apparu en premier sur VAG Coding.

Purpose: activates High Beam Assist for vehicles with Sign Assist and/or Lane Assist options.

Caution: Please use these instructions only on vehicles equipped with Xenon headlights or “simple/static” LED headlights. In vehicles equipped with Matrix LED, this function is always active at the factory.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“05”
Tick Bit 0“mmi_fla_glw_mxb,active”
Then in the Bit “5-7” drop-down menu, select“60 high_beam_functions,head_light_assistant”.

Line 2:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“21”
Then, in the“Bit 5-7” drop-down menu, select “20 AFS_coding_Light_Assist,High_Beam_Assist”

L’article Q7 (4M) – High Beam Assist activation est apparu en premier sur VAG Coding.

Purpose: activates High Beam Assist for vehicles with Sign Assist or Lane Assist option.

Caution: Please use these instructions only on vehicles equipped with Xenon headlights or “simple/static” LED headlights. In vehicles equipped with Matrix LED, this function is always active at the factory.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“05”
Tick Bit 0“mmi_fla_glw_mxb,active”
Then in the Bit “5-7” drop-down menu, select“60 high_beam_functions,head_light_assistant”.

Line 2:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“67”
Then, in the“Bit 2-5” drop-down menu, select“04 AFS_coding_Light_Assist,High_Beam_Assist”.

L’article Q8 (4M) – High Beam Assist activation est apparu en premier sur VAG Coding.