Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article Golf 8 (5H) – Enable Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the installation of a retrofit trailer hitch (trailer/towbar retrofit).

Warning!! Depending on the modules you have installed, there are up to 9 coding lines to complete here; most control units require a long coding process with a “trailer” that must be enabled!

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Select “Installation List”

5 – Check “69 – Trailer” in the list

6 – Save coding

Line 2:

3 – Click on“Select”, then click on“01 – Motor“.

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “05“
. Then check bit “4“: “Trailer installed“

Line 3:

3 – Click “Select,” then click ““09 – Cent. Elect.”“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vernetzung – Anhaengeranschlussgeraet“

7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “installed” and then confirm.

Line 4:

3 – Click on“Select” then click on“03 – ABS brake“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Gespannstabilisierung.”

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Active” and then confirm.

Line 5:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg. “.

4 – Unlock SFD protection

5 – Click ” Encoding – 07,” then click “Long Coding Helper“

6 – Select byte “01“
Then check Bit 7 “Control_module_for_towing_sensor”

Line 6:

3 – Click “Select,” then click “3C – Lane Change.”

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select the “00” byte
Then check Bit 5 “ECU for drawbar, with ECU for drawbar”



Line 7:

3 – Click “Select,” then click “6C – Rearview Camera.”

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “02“
Then set bit 0 (“equipment_ahk, installed”)



Line 8:

3 – Click on“Select” then click on “.A5 – Front, Sensors, Driver Assistance “.

4 – Unlock SFD protection

5 – Click ” Encoding – 07,” then click “Long Coding Helper“

Select byte “05“

Then set bit 4 (“AAG, 0 = not_coded / 1 = coded”)

Line 9:

3 – Click “Select,” then click “69 – Trailer“.

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “01“
Then check bits 0-7 “01 – Trailer Connector Diagnostics active”

Select byte “03“
Then check bits 0-7 “01 – Trailer Connector Diagnostics active”

L’article Golf 8 (5H) – Enable the trailer hitch (retrofit) est apparu en premier sur VAG Coding.

Purpose: Allows two phones to be connected simultaneously to the MIB via Bluetooth.


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “Vehicle configuration – Support_second_phone“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “two” and then confirm.

Restart MMI

L’article Golf 8 (5H) – Pair a Second Phone via Bluetooth est apparu en premier sur VAG Coding.

Purpose: to unlock the limitations of Android Auto, allowing access to all functions without the restrictions imposed by default on the multimedia system.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_limit_displayed_message_length”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 2:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_text_input”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 3:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_video_playback”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 4:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_setup_configuration”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

L’article Golf 8 (5H) – Unlock Android Auto’s Limitations est apparu en premier sur VAG Coding.

Purpose: Allows you to unlock certain multimedia system menus while driving, which are normally locked when the vehicle is in motion.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select:

Disabled_menu_contents – FB_MEDIA_19
FB_MISC_14
FB_MISC_19
FB_MISC_18
FB_MISC_31
FB_MISC_29
FB_MISC_25
FB_MISC_33
FB_MISC_44
FB_MISC_41

7 – On this same page is a second drop-down menu, but at the bottom
of the page.
On this, choose“non_blocked” then validate.

L’article Golf 8 (5H) – Unlocking the Menus While Driving est apparu en premier sur VAG Coding.

Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-sided operation via the blinker switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Standlicht – Parklicht ueber LSS aktiviert”.

7 – On this same page, there’s a second drop-down menu, at the bottom
of the page.
On this menu, select ” Dual Sided ” and confirm.

L’article Golf 8 (5H) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: activates the IQ.LIGHT headlamp presentation mode when the ignition is switched on or the engine started, to create a dynamic light animation (showroom effect).

SFD: yes


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or your OBDeleven box.

2 – Switch on the ignition and run the VCDS program. or the OBDeleven application. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select” then click on“4B – Multifunction Module“.

4 – Unlock the SFD protection.

5 – Click on“Adaptation – 10“.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, select the “Reference_Run_Start_Condition” channel.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, select“Motorstart / “Klemme 15” when turning on the ignition“, then confirm.

Line 2:

3 – Click on“Select” then click on“4B – Multifunction Module“.

4 – Unlock the SFD protection.

5 – Click on“Adaptation – 10“.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, select the “Reference_Run_Activation_Effect” channel.

7 – On this same page, there is a second drop-down menu, at the bottom
of the page.
On this menu, select“Activation effect enabled by motor start” to activate when the motor is started, or“Activation effect enabled by clamp 15” to activate when the ignition is switched on, then confirm.

L’article Golf 8 (5H) – IQ.LIGHT presentation mode est apparu en premier sur VAG Coding.

Purpose: to activate the locking and unlocking of the central locking system with the KESSY keyless entry system, when moving away from the vehicle.

SFD: yes

Warning! There are 6 lines of coding to do here.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Automatische_Funktionen – Automatisches_Verriegeln_aktiv“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“DevCod_IDGeber_Suche – Unterdrueckung_zyklischer _Suchen_bei_entriegeltem_Fahrzeug_aktiv“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“DevCod_Nutzerkonfigurationen – HMIMenue_Aktivierung_Nah_Mittel_Fern_aktiv“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 4:

3 – Click on“Select”, then click on“B7 – Access Startsystem Interface”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose“Passive_Komfort – Passive_Komfort_Oeffnen_aktiv”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 5:

3 – Click on“Select”, then click on“B7 – Access Startsystem Interface”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Passive_Komfort – Passive_Komfort_Togglen_aktiv”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 6:

3 – Click on“Select”, then click on“B7 – Access Startsystem Interface”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“DevCod_AutomatischeFunktionen – Slowpolling_Rechtecksignal_Aktiv“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Note:

Only possible with software version 0174 or higher.
Not possible with a lower version.
A “High” BCM is also required!
Under ECU identification.
BCM37w_H = OK
BCM37w_M1 = OK
BCM37_M Hardware L = No OK
Does not work if you move away from the tailgate.
The control unit with address B7 is also required!

L’article Golf 8 (5H) – Automatic locking when driving away est apparu en premier sur VAG Coding.

Purpose: to change the color of the ambient light according to the driving profile selected.

SFD: yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or OBDeleven.

2 – Switch on the ignition and run the VCDS program. or OBDeleven.

Line 1:

3 – Click on ” Select”, then click on ” 09 – Cent. Elect. “.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the ” Interior_light_general_settings ” channel.

6 – Select the profile then modify the value according to the desired color.

Mapping_fpa_profile_1 (Light blue) 1
Mapping_fpa_profile_2 (Blue) 5
Mapping_fpa_profile_3 (Red) 3
Mapping_fpa_profile_4 (Lime) 4
Mapping_fpa_profile_5 (Violet) 2
Mapping_fpa_profile_6 (Yellow) 7

1 = Comfort
3 = Sport
4 = Offroad
5 = Eco
6 = Race
7 = Individual

L’article Golf 8 (5H) – Change ambient colors for driving profiles est apparu en premier sur VAG Coding.

Purpose: to adjust seat heater temperature levels. Note that temperature values for individual steps must be set in ascending order.
Please check the number of seat heating levels your vehicle supports before changing. Not all vehicles support levels 1 to 6.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose :

Seat_Heating_Level_Adaptation:

• Seat_heating_stage_1_lower_threshold: 20,0°C (stage 1)
• Seat_heating_stage_1_upper_threshold: 20,5°C (stage 1)
• Seat_heating_stage_2_lower_threshold: 20,0°C (stage 1)
• Seat_heating_stage_2_upper_threshold: 20,5°C (stage 1)
• Seat_heating_stage_3_lower_threshold: 33,0°C (stage 2)
• Seat_heating_stage_3_upper_threshold: 33.5°C (stage 2)
• Seat_heating_stage_4_lower_threshold: 33,0°C (stage 2)
• Seat_heating_stage_4_upper_threshold: 33.5°C (stage 2)
• Seat_heating_stage_5_lower_threshold: 50,0°C (stage 3)
• Seat_heating_stage_5_upper_threshold: 50,5°C (stage 3)
• Seat_heating_stage_6_lower_threshold: 50,0°C (stage 3)
• Seat_heating_stage_6_upper_threshold: 50,5°C (stage 3)

OR

• “IDE06089-ENG263544-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_1_lower_threshold”
• “IDE06089-ENG263507-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_1_upper_threshold”
• “IDE06089-ENG263592-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_2_lower_threshold”
• “IDE06089-ENG263559-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_2_upper_threshold”
• “IDE06089-ENG263539-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_3_lower_threshold”
• “IDE06089-ENG263539-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_3_lower_threshold”
• “IDE06089-ENG263536-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_4_lower_threshold”
• “IDE06089-ENG263549-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_4_upper_threshold”
• “IDE06089-ENG263566-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_5_lower_threshold”
• “IDE06089-ENG263597-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_5_upper_threshold”
• “IDE06089-ENG263562-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_6_lower_threshold”
• “IDE06089-ENG263524-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_6_upper_threshold”

6 – On this same page, there’s a second drop-down menu, but at the bottom
of the page.
Adjust the values as required. “Lower” is the activation temperature and “higher” is the deactivation temperature.

L’article Golf 8 (5H) – Adjusting heated seat temperature est apparu en premier sur VAG Coding.