Purpose: Resets the settings for all remote controls associated with the vehicle.

WARNING: After completing this procedure, all remote controls will be deleted and will need to be reprogrammed using the “Program a Remote Control” tutorial .
If your vehicle is equipped with a KESSY remote control (05 – Access/Start Authorization), you cannot delete the remote controls using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set the value to 0 and save

L’article Altea (5P) Facelift – Resetting the Remote Controls est apparu en premier sur VAG Coding.

Purpose: Allows you to program the remote controls that will be used with the vehicle for central locking and unlocking.

WARNING: This procedure does not allow you to program remote controls with the vehicle’s immobilizer.
If your vehicle is equipped with a KESSY remote control (05 – Access/Ignition Authorization), you cannot program a new remote control using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 ( “Remote Control Adaptation” from the drop-down list)

Enter the number of keys to program, then click Save.
Next, press the Unlock button on each remote control to be programmed for at least 1 second. The flashing lights will confirm the process.
All keys must be programmed in a single session, one after the other.
Programming all keys must not take longer than 15 seconds.
You can add up to 7 remote controls. If the [Test] and/or [Save] buttons are grayed out and unclickable, the module likely has all 7 slots filled; delete the remote controls using the “Reset Remote Controls” tutorial.

L’article Altea (5P) Facelift – Programming a Remote Control est apparu en premier sur VAG Coding.

Purpose: Resets the settings for all remote controls associated with the vehicle.

WARNING: After completing this procedure, all remote controls will be deleted and will need to be reprogrammed using the “How to Program a Remote Control” tutorial .

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set the value to 0 and save

L’article Altea (5P) – Reset the remote controls est apparu en premier sur VAG Coding.

Purpose: Allows you to program the remote controls that will be used with the vehicle for central locking and unlocking.

WARNING: This procedure does not allow you to program the remote controls with the vehicle’s immobilizer.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 ( “Remote Control Adaptation” from the drop-down list)

Enter the number of keys to program, then click Save.
Next, press the Unlock button on each remote control to be programmed for at least 1 second. The flashing lights will confirm the procedure.
All keys must be programmed in a single session, one after the other.
Programming all keys must not take longer than 15 seconds.
You can add up to 4 remote controls. If the [Test] and/or [Save] buttons are grayed out and unclickable, the module likely has all 4 slots filled; delete the remote controls using the “Reset Remote Controls” tutorial.

L’article Altea (5P) – Programming a Remote Control est apparu en premier sur VAG Coding.

Purpose: Allows you to correct the fuel consumption display on the onboard computer.

This setting can only be changed on mid-range and high-end models.
Note: Changes made to this setting affect the display of instantaneous fuel consumption, average fuel consumption, and fuel level.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “ Select,” then click “17 – Instruments.”

4 – Click “Adaptation – 10.”

5 – Select Channel 03 “Consumption Correction”

Set the consumption correction factor between 85% and 115% (base value: 100)

Example 1: Calculation based on volume per distance (e.g., l/100 km): Specified: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9.8 / 9.73 ? 105.38) Channel 3 will be changed from 100 to 105
Example 2: Calculation based on distance per volume (e.g., MPG): Target: 23 MPG. Actual: 24 MPG. (100, 23/24, and 95.83) Channel 3 will be changed from 100 to 96

L’article Altea (5P) – Fixed the OBD fuel consumption display est apparu en premier sur VAG Coding.

Purpose: Allows you to adjust the power steering stiffness for a smoother or stiffer, sportier steering feel.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “44 – Power Steering” / “44-steering assist.”

4 – Click “Adaptation – 10“

5 – Select Channel 1, then enter a value between 1 and 15 based on your preferred hardness level

Or Line 2: (If Channel 1 is unavailable):

3 – Click “Select,” then click “44 – Power Steering” / “44-steering assist.”

4 – Click on “Coding – 07“

5 – Choose :

• xxx1x for smooth steering
• xxx2x for a sporty ride
• xxx3x for a stiff steering feel
• xxx4x for a firmer steering feel
• xxx5x for very stiff steering

L’article Altea (5P) – Adjusting the power steering stiffness est apparu en premier sur VAG Coding.

Purpose: automatically lowers the passenger mirror when reversing.

The mirror adjustment knob must be in position“R” for the passenger mirror to lower automatically.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “09 – Centrale Elec”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – In the window that appears, select byte 4 and check bit 3 “ Mirror Lowering With Reverse Rear ” to activate mirror lowering when shifting into reverse gear:

6 – After this operation, click on the “Output” menu, then validate “OK”.

A message appears to inform you that the coding has been accepted.

Line 2:

3 – Click on “Select” , then click on “52 – Passenger door”.

4 – Click on “Coding – 07”.

Add 256 to the value

L’article Altea (5P) Facelift – Lowering the passenger mirror when reversing est apparu en premier sur VAG Coding.

Purpose: Enables the rearview camera after it has been installed on the RCD 510/330/360/440 and RNS 315/510 (retrofit).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “37 – Navigation ” (RNS) or “56 – Radio” (RCD)

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte 3
. Then set bit 6 to “Rear View Camera (RVC) installed/active.”

Line 2 (Optional, if parking assist is available) :

3 – Click “Select,” then click “10 – Parking Assistance.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte 0
. Then set bit 5 to “Rear View Camera installed.”

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The two pins from the backup camera are used in the 12-pin Quadlock connector (blue).

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Altea (5P) Facelift – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Altea (5P) Facelift – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Altea (5P) Facelift – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.