Purpose: Allows you to reprogram or recode all data for the new battery after it has been replaced.

SFD: yes

Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click ” Adaptation – 10.”

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Battery Adaptation—Nominal Battery Capacity.”

6 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select the rated capacity listed on your battery. For example: “70Ah“

Line 2:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Adaptation – 10.”

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Battery Adaptation—Battery Technology.”

6 – On this same page, there is a second drop-down menu further down
.
From this menu, select the corresponding value
. For example: For the VARTA E39, select “Etoffe” / “Fleece” for AGM.

Line 3:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Adaptation – 10.”

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Battery Adaptation—Battery Manufacturer.”

6 – On this same page, there is a second drop-down menu further down the page
.
From this menu, select the corresponding brand:
For example: For the VARTA E39, select “VAO.”

Line 4:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Adaptation – 10.”

5 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Battery Configuration—Battery Serial Number.”

6 – On this same page, there is a second drop-down menu toward the bottom
.
In this menu, enter the corresponding serial number:
Note: Enter only the last 10 digits of the serial number.

Battery Status Detection Features:

Battery status detection in the battery data module calculates the following quantities, which are transmitted via the LIN bus to the J533 data bus diagnostics interface:
1 “Battery non-existent” detection: if the battery data module detects no battery for
more than 30s, a corresponding bit is set to a
2 voltage momentarily allowing optimum charging of the battery
3 “Motor startability” bit. This indicates whether or not the battery is momentarily able to start
the engine
4 charge that can momentarily still be drawn from the battery before reaching the
engine startability limit
5 current state of charge of the battery
6 battery ageing. Battery ageing can be determined via quantities such as energy storage capacity and momentary battery power.
7 battery quiescent voltage
8 battery internal resistance

The battery sensor in the J367 battery monitoring control unit:

Knowing whether the battery has enough electrical energy to restart the engine is essential for the start-stop system to function properly.
The control module is located directly on the “negative” terminal of the ground wire and is connected to the diagnostic interface via the LIN data bus.

Signal Usage:
The battery sensor records the following values:
– Battery temperature
– Battery voltage
– Charging current
The battery temperature is calculated using a lookup table and the ambient temperature.
It also allows for estimates of the battery’s charging time.
Using the data obtained in this way, it is possible to adjust the charging control—particularly the charging voltage—to the battery’s state of charge and operating conditions. The goal is to increase the availability of the start-stop system by optimally utilizing data from the starter battery.

Consequences in the Event of a Malfunction
If the battery sensor is defective, the battery status can no longer be detected correctly.
A fault is logged in the diagnostic interface’s fault memory. The start-stop system is deactivated.

Battery

The vehicle’s battery is housed in the engine compartment and protected by a battery tray. The size and type of battery depend on the engine version, equipment, and country-specific variant. Standard batteries, EFB batteries, and AGM batteries are used.
Vehicles with gasoline engines and start/stop systems are equipped with an EFB battery, while vehicles with diesel engines and start/stop systems are equipped with an AGM battery. Vehicles with auxiliary heaters typically have an AGM battery.

EFB

An EFB battery (short for Enhanced Flooded Battery) is a reinforced flooded battery. The positive plate inside the battery is coated with an additional layer of polyester mesh. This provides the battery’s active material with additional support on the plate. These batteries have greater resistance to charge-discharge cycles than standard batteries. During charging, an EFB battery is treated like a standard battery.

AGM Battery

In AGM (Absorbent Glass Mat) batteries, the battery electrolyte is retained within a microporous glass mat. An AGM battery is characterized not only by even greater resistance to charge-discharge cycles compared to an EFB battery, but also by its leak-proof design. When charging, follow the charger’s user manual and, if applicable, select the AGM battery program.

In the case of AGM batteries, the automotive battery electrolyte is retained in a micro-porous glass mat. In addition to
increased resistance to alternating cycles, an AGM battery is characterized by its good sealing properties. Waterproofing is of crucial importance
, especially when the battery is installed in the passenger compartment. When charging, please follow the charger’s operating instructions and select the program for
AGM battery, if applicable.

Below, we can see the brand, serial number, and manufacturer of the battery

L’article A3 (8Y) – Reprogramming a new battery est apparu en premier sur VAG Coding.

Purpose: Allows you to unlock certain multimedia system menus while driving, which are normally locked when the vehicle is in motion.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select:

Disabled_menu_contents – FB_MEDIA_19
FB_MISC_14
FB_MISC_19
FB_MISC_18
FB_MISC_31
FB_MISC_29
FB_MISC_25
FB_MISC_33
FB_MISC_44
FB_MISC_41

7 – On this same page is a second drop-down menu, but at the bottom
of the page.
On this, choose“non_blocked” then validate.

L’article A3 (8Y) – Unlocking the menus while driving est apparu en premier sur VAG Coding.

Purpose: to unlock the limitations of Android Auto, allowing access to all functions without the restrictions imposed by default on the multimedia system.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_limit_displayed_message_length”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 2:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_text_input”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 3:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_video_playback”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 4:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_setup_configuration”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

L’article A3 (8Y) – Bypass Android Auto’s Limitations est apparu en premier sur VAG Coding.

Purpose: Allows you to connect two phones via Bluetooth simultaneously to the Audi MMI.


SFD: Yes

Procedure:
1 – With the engine off and the ignition off, connect your official VAG-COM VCDS cable to the computer, then connect the other end to your vehicle’s diagnostic port or your OBDeleven unit.

2 – Turn on the ignition, then launch the VCDS program or the OBDeleven app.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “Vehicle configuration – Support_second_phone“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “two” and then confirm.

Restart MMI

L’article A3 (8Y) – Pair a second phone via Bluetooth est apparu en premier sur VAG Coding.

Purpose: Enables the installation of a retrofit trailer hitch (trailer/towbar retrofit).

Warning!! Depending on the modules you have installed, there are up to 9 coding lines to complete here; most control units require a long coding process with a “trailer” that must be enabled!

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Select “Installation List”

5 – Check “69 – Trailer” in the list

6 – Save coding

Line 2:

3 – Click on“Select”, then click on“01 – Motor“.

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “05“
. Then check bit “4“: “Trailer installed“

Line 3:

3 – Click “Select,” then click ““09 – Cent. Elect.”“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vernetzung – Anhaengeranschlussgeraet“

7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “installed” and then confirm.

Line 4:

3 – Click on“Select” then click on“03 – ABS brake“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Gespannstabilisierung.”

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Active” and then confirm.

Line 5:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg. “.

4 – Unlock SFD protection

5 – Click ” Encoding – 07,” then click “Long Coding Helper“

6 – Select byte “01“
Then check Bit 7 “Control_module_for_towing_sensor”

Line 6:

3 – Click “Select,” then click “3C – Lane Change.”

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select the “00” byte
Then check Bit 5 “ECU for drawbar, with ECU for drawbar”



Line 7:

3 – Click “Select,” then click “6C – Rearview Camera.”

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “02“
Then set bit 0 (“equipment_ahk, installed”)



Line 8:

3 – Click on“Select” then click on “.A5 – Front, Sensors, Driver Assistance “.

4 – Unlock SFD protection

5 – Click ” Encoding – 07,” then click “Long Coding Helper“

Select byte “05“

Then set bit 4 (“AAG, 0 = not_coded / 1 = coded”)

Line 9:

3 – Click “Select,” then click “69 – Trailer“.

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “01“
Then check bits 0-7 “01 – Trailer Connector Diagnostics active”

Select byte “03“
Then check bits 0-7 “01 – Trailer Connector Diagnostics active”

L’article A3 (8Y) – Enable the trailer hitch (retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article A3 (8Y) – Enable Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-sided operation via the blinker switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Standlicht – Parklicht ueber LSS aktiviert”.

7 – On this same page, there’s a second drop-down menu, at the bottom
of the page.
On this menu, select ” Dual Sided ” and confirm.

L’article A3 (8Y) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: to adjust seat heater temperature levels. Note that temperature values for individual steps must be set in ascending order.
Please check the number of seat heating levels your vehicle supports before changing. Not all vehicles support levels 1 to 6.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose :

Seat_Heating_Level_Adaptation:

• Seat_heating_stage_1_lower_threshold: 20,0°C (stage 1)
• Seat_heating_stage_1_upper_threshold: 20,5°C (stage 1)
• Seat_heating_stage_2_lower_threshold: 20,0°C (stage 1)
• Seat_heating_stage_2_upper_threshold: 20,5°C (stage 1)
• Seat_heating_stage_3_lower_threshold: 33,0°C (stage 2)
• Seat_heating_stage_3_upper_threshold: 33.5°C (stage 2)
• Seat_heating_stage_4_lower_threshold: 33,0°C (stage 2)
• Seat_heating_stage_4_upper_threshold: 33.5°C (stage 2)
• Seat_heating_stage_5_lower_threshold: 50,0°C (stage 3)
• Seat_heating_stage_5_upper_threshold: 50,5°C (stage 3)
• Seat_heating_stage_6_lower_threshold: 50,0°C (stage 3)
• Seat_heating_stage_6_upper_threshold: 50,5°C (stage 3)

OR

• “IDE06089-ENG263544-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_1_lower_threshold”
• “IDE06089-ENG263507-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_1_upper_threshold”
• “IDE06089-ENG263592-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_2_lower_threshold”
• “IDE06089-ENG263559-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_2_upper_threshold”
• “IDE06089-ENG263539-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_3_lower_threshold”
• “IDE06089-ENG263539-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_3_lower_threshold”
• “IDE06089-ENG263536-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_4_lower_threshold”
• “IDE06089-ENG263549-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_4_upper_threshold”
• “IDE06089-ENG263566-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_5_lower_threshold”
• “IDE06089-ENG263597-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_5_upper_threshold”
• “IDE06089-ENG263562-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_6_lower_threshold”
• “IDE06089-ENG263524-Zuordnung der Stromaufnahme für Sitzheizungsstufen-Seat_heating_stage_6_upper_threshold”

6 – On this same page, there’s a second drop-down menu, but at the bottom
of the page.
Adjust the values as required. “Lower” is the activation temperature and “higher” is the deactivation temperature.

L’article A3 (8Y) – Adjust temperature of heated seats est apparu en premier sur VAG Coding.

Purpose: to activate the closing and opening of the windows and sunroof with the KESSY keyless entry system. press and hold the handle until the windows are fully closed or open.

SFD: yes

Warning! There are 5 lines of coding to do here.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Kessyfunktion – Komfortbedienung_fh_oeffnen_ueber_kessy”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Komfort_Fensterheber – Komfortbedienung_fh_oeffnen_ueber_sz”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Komfort_Fensterheber – Komfort_oeffnen”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 4:

3 – Click on“Select”, then click on“B7 – Access Startsystem Interface”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Passive_Komfort – Passive_Komfort_Oeffnen_aktiv”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

Line 5:

3 – Click on“Select”, then click on“B7 – Access Startsystem Interface”.

4 – Click on“Security Access – 16” then enter the code“10587”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Passive_Komfort – Passive_Komfort_Togglen_aktiv”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

L’article A3 (8Y) – Opening/closing windows with KESSY est apparu en premier sur VAG Coding.

Purpose: to deactivate the active ignition alert when the engine is running or a door is open.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ Unterdrückung Zündungswarnung – Ausgabe MoLaWa_AAW”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Deactivated” and confirm.

L’article A3 (8Y) – Deactivate active ignition warning with engine running/door open. est apparu en premier sur VAG Coding.