Purpose: Allows you to unlock certain multimedia system menus while driving, which are normally locked when the vehicle is in motion.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select:

Disabled_menu_contents – FB_MEDIA_19
FB_MISC_14
FB_MISC_19
FB_MISC_18
FB_MISC_31
FB_MISC_29
FB_MISC_25
FB_MISC_33
FB_MISC_44
FB_MISC_41

7 – On this same page is a second drop-down menu, but at the bottom
of the page.
On this, choose“non_blocked” then validate.

L’article A3 (8Y) – Unlocking the menus while driving est apparu en premier sur VAG Coding.

Purpose: to unlock the limitations of Android Auto, allowing access to all functions without the restrictions imposed by default on the multimedia system.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_limit_displayed_message_length”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 2:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_text_input”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 3:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_video_playback”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 4:

3 – Click “Select,” then click “5F – Electrical Information“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “nhtsa_properties – nhtsa_limitation_switches_for_androidauto_no_setup_configuration”

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

L’article A3 (8Y) – Bypass Android Auto’s Limitations est apparu en premier sur VAG Coding.

Purpose: Allows two phones to be connected simultaneously to the MIB via Bluetooth.


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
In this drop-down menu, select “Vehicle configuration – Support_second_phone“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “two” and then confirm.

Restart MMI

L’article A3 (8Y) – Pair a second phone via Bluetooth est apparu en premier sur VAG Coding.

Purpose: Enables the installation of a retrofit trailer hitch (trailer/towbar retrofit).

Warning!! Depending on the modules you have installed, there are up to 9 coding lines to complete here; most control units require a long coding process with a “trailer” that must be enabled!

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Select “Installation List”

5 – Check “69 – Trailer” in the list

6 – Save coding

Line 2:

3 – Click on“Select”, then click on“01 – Motor“.

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “05“
. Then check bit “4“: “Trailer installed“

Line 3:

3 – Click “Select,” then click ““09 – Cent. Elect.”“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vernetzung – Anhaengeranschlussgeraet“

7 – On this same page, there is a second drop-down menu toward the bottom
.
From this menu, select “installed” and then confirm.

Line 4:

3 – Click on“Select” then click on“03 – ABS brake“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Gespannstabilisierung.”

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Active” and then confirm.

Line 5:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg. “.

4 – Unlock SFD protection

5 – Click ” Encoding – 07,” then click “Long Coding Helper“

6 – Select byte “01“
Then check Bit 7 “Control_module_for_towing_sensor”

Line 6:

3 – Click “Select,” then click “3C – Lane Change.”

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select the “00” byte
Then check Bit 5 “ECU for drawbar, with ECU for drawbar”



Line 7:

3 – Click “Select,” then click “6C – Rearview Camera.”

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “02“
Then set bit 0 (“equipment_ahk, installed”)



Line 8:

3 – Click on“Select” then click on “.A5 – Front, Sensors, Driver Assistance “.

4 – Unlock SFD protection

5 – Click ” Encoding – 07,” then click “Long Coding Helper“

Select byte “05“

Then set bit 4 (“AAG, 0 = not_coded / 1 = coded”)

Line 9:

3 – Click “Select,” then click “69 – Trailer“.

4 – Click on ” Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “01“
Then check bits 0-7 “01 – Trailer Connector Diagnostics active”

Select byte “03“
Then check bits 0-7 “01 – Trailer Connector Diagnostics active”

L’article A3 (8Y) – Enable the trailer hitch (retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article A3 (8Y) – Enable Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: Allows the windows to be opened slightly when the driver’s or passenger’s door is open. When a window is lowered, the cabin is no longer completely sealed, allowing the doors to be closed gently without having to slam them shut. (Windows Auto Drop)


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“


Line 2:

3 – Click “Select,” then click “42 – Driver’s Door.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“

L’article Q8 (4M) – Enable automatic window lowering est apparu en premier sur VAG Coding.

Purpose: Allows the windows to be opened slightly when the driver’s or passenger’s door is open. When a window is lowered, the cabin is no longer completely sealed, allowing the doors to be closed gently without having to slam them shut. (Windows Auto Drop)


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“


Line 2:

3 – Click “Select,” then click “42 – Driver’s Door.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“

L’article Q7 (4M) – Enable automatic window lowering est apparu en premier sur VAG Coding.

Purpose: Allows the windows to be slightly ajar when the driver’s or passenger’s door is open. When a window is lowered, the cabin is no longer completely sealed, allowing the doors to be closed gently without having to slam them shut. (Windows Auto Drop)


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“


Line 2:

3 – Click “Select,” then click “42 – Driver’s Door.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“

L’article Q5 (FY) – Enable automatic window lowering est apparu en premier sur VAG Coding.

Purpose: Allows the windows to be slightly ajar when the driver’s or passenger’s door is open. When a window is lowered, the cabin is no longer completely sealed, allowing the doors to be closed gently without having to slam them shut. (Windows Auto Drop)


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“


Line 2:

3 – Click “Select,” then click “42 – Driver’s Door.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“

L’article A8 (D5) – Enable automatic window lowering est apparu en premier sur VAG Coding.

Purpose: Allows the windows to be slightly ajar when the driver’s or passenger’s door is open. When a window is lowered, the cabin is no longer completely sealed, allowing the doors to be closed gently without having to slam them shut. (Windows Auto Drop)


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“


Line 2:

3 – Click “Select,” then click “42 – Driver’s Door.”

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte “3“
. Then uncheck bit “1“: “short_drop,active“

L’article A7 (C8) – Enable automatic window lowering est apparu en premier sur VAG Coding.