Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of frost. (Origin: 4°C)
Then choose“Outsitde temperature p ice warning exit temperature” for the value at which the frost alert ends. (Origin: 6°C)

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Q2 (GA) – Modify warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of frost. (Origin: 4°C)
Then choose“Outsitde temperature p ice warning exit temperature” for the value at which the frost alert ends. (Origin: 6°C)

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Tarraco (KN) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of freezing.
Then choose“Outsitde temperature p ice warning exit temperature” for the end of freezing alert value.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Karoq (NU) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of freezing.
Then choose“Outsitde temperature p ice warning exit temperature” for the end of freezing alert value.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Kodiaq (NS) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of frost. (Origin: 4°C)
Then choose“Outsitde temperature p ice warning exit temperature” for the value at which the frost alert ends. (Origin: 6°C)

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Polo 6 (AW1) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: to display oil temperature on the Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“10”
Then check Bit“1”:“Display Oil Temperature”.

L’article Tarraco (KN) – Oil temperature on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: Allows you to modify and customize the Active Info Display / Virtual Cockpit in order to increase the speedometer’s maximum speed. (For AID v1)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “Tube illustration / version” channel.

6 – In the “Value:” option, choose one of the 4 variants

Variant 0: Default

Variant 1: Normal (max 260km/h)

Variant 2: AllTrack (max 260km/h)

Variant 3: GTI (max 280km/h)

Variant 4: R (max 320km/h)

L’article T-Roc (A1) – Meter display on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: to modify and customize the Active Info Display / Virtual Cockpit. Depending on the setting, the display of the counter and/or vmax is different.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 (To change counter background) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “Tube illustration” / “Tube representation” channel.

6 – In the “Value:” option, select one of the following versions:

Version 0

Version 1

Version 2

Version 3 (Cupra bronze):

Version 8: Cupra

For Sport Cupra central counter see tuto :

Line 2 (To modify Vmax) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “Tachometer end value” channel.

6 – In the “Value:” option, choose one of the 3 versions:

Version 0 – 260 km/h
Version 2 – 240 km/h
Version 3 – 300 km/h

L’article Tarraco (KN) – Changing the Virtual Cockpit display est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the Trip Computer/Virtual Cockpit.

Note: these changes affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel: “Display correction of consumptions and operating range”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96.

Example 3: the consumption announced by the ODB is 5.9l/100km, after checking it is actually 6.3l/100km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%, and the consumption announced by the ODB will be a pessimistic 0.1l/100km.

Consumption is immediately modified on the MMI.

L’article Q7 (4M) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: to change the startup logo displayed on the Virtual Cockpit.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 9 and check the bits according to your preference:

Bit 0-2 select Variant :

L’article Q5 (FY) – Virtual Cockpit start logo est apparu en premier sur VAG Coding.