Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation. (For Phase 1)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 4

Disable bit 7 ” Brake Pad Wear Sensor installed “

Restart the vehicle so that the warning light is no longer displayed.

L’article Q2 (GA) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: Activates the gearshift recommendation. The gearshift recommendation is then displayed in the lower section of the ODB.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte“1“
Then check Bit“5“.

L’article Q2 (GA) – Activate gearshift recommendation est apparu en premier sur VAG Coding.

Purpose: Allows you to choose the language of your on-board computer. For an A3 8V imported from abroad, for example.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Variante linguistique” /“Language Version“.

7 – Select language from second value list

L’article Q2 (GA) – Change ODB language est apparu en premier sur VAG Coding.

Purpose: To activate or deactivate a message reminding you that you are exceeding the 120km/h speed limit.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte“0”
Then check to enable or uncheck to disable the box in“6”:“Speed warning at 120 kph (75 mph) active“.

L’article Q2 (GA) – 120 km/h overrun warning est apparu en premier sur VAG Coding.

Purpose: to display a compass on the ODB (on-board computer), if you have GPS navigation (NAV), and to change its position on the speedo.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – instruments“.

4 – Click on“Coding – 07“, then on“Long Coding Helper“.

5 – Select byte“10“
Then check Bit“6“.

Line 2 (if line 1 unavailable) :

3 – Click on ” Select”, then click on ” 17- Instruments “.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the ” Navigation /Compass” channel.

6 – In the ” Value: ” option, select“Enabled“.

Line 3 (to change the compass position on the ODB) :

3 – Click on ” Select”, then click on ” 17- Instruments “.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. From this drop-down menu, select the “Compass indicator ” channel.

6 – In the ” Value: ” option, select the desired value for the compass position on the ODB (default: lower position).

L’article Q2 (GA) – Compass display on ODB est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of frost. (Origin: 4°C)
Then choose“Outsitde temperature p ice warning exit temperature” for the value at which the frost alert ends. (Origin: 6°C)

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Q2 (GA) – Modify warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of frost. (Origin: 4°C)
Then choose“Outsitde temperature p ice warning exit temperature” for the value at which the frost alert ends. (Origin: 6°C)

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Tarraco (KN) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of freezing.
Then choose“Outsitde temperature p ice warning exit temperature” for the end of freezing alert value.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Karoq (NU) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of freezing.
Then choose“Outsitde temperature p ice warning exit temperature” for the end of freezing alert value.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Kodiaq (NS) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.

Purpose: Allows you to select the outside temperature value for the risk of icy conditions for which the warning is displayed on the dashboard (Ice Warning).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Outsitde temperature p ice warning entry temperature” for the value at which the alert sounds to warn of frost. (Origin: 4°C)
Then choose“Outsitde temperature p ice warning exit temperature” for the value at which the frost alert ends. (Origin: 6°C)

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose the temperature value you want.

L’article Polo 6 (AW1) – Change warning thresholds for icy conditions est apparu en premier sur VAG Coding.