Purpose: Disables license plate light control. Useful when installing LED bulbs without resistance or for error prevention.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 23:

Bit 6: Uncheck: “Lamp Monitoring (Cold) License Plate Lamps Active”.

L’article Passat (B7) – Disable plate illumination control (ODB LED error) est apparu en premier sur VAG Coding.

Purpose: To deactivate the burnt-out bulb indicator on the ODB (on-board computer). After adding LEDs, your on-board computer may indicate that the replaced bulb is out of order.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 18 Bit 0: Uncheck “Cold Diagnosis License Plate Lights active” for plates

the other bits for the other bulbs of your choice (see image)

Byte 19 Bit 1: uncheck “Cold Diagnosis Front Parking Lights active” for night lights

Or for all bulbs:

Byte 2 Bit 2: Cold Lamp Diagnosis Active

Eliminate burnt-out bulb errors after coding.

L’article Touran (1T) – Deactivate burnt-out bulb display est apparu en premier sur VAG Coding.

Purpose: To deactivate the burnt-out bulb indicator on the ODB (on-board computer). After adding LEDs, your on-board computer may indicate that the replaced bulb is out of order.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 18 Bit 0: Uncheck “Cold Diagnosis License Plate Lights active” for plates

the other bits for the other bulbs of your choice (see image)

Byte 19 Bit 1: uncheck “Cold Diagnosis Front Parking Lights active” for night lights

Or for all bulbs:

Byte 2 Bit 2: Cold Lamp Diagnosis Active

Eliminate burnt-out bulb errors after coding.

L’article Caddy (2K) – Deactivate burnt-out bulb display est apparu en premier sur VAG Coding.

Purpose: Eliminates ODB error after LED reversing light installation.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64 – Lasttyp 29”.

7 – On the same page, there is a second drop-down menu at the bottom
of the page.
Select“43 – allgemeine LED” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64 – Dimmwert AB29”

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose “127” then validate.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte28RFL LC11 – Lasttyp 28”.

7 – On the same page, there is a second drop-down menu at the bottom
of the page.
Select“43 – allgemeine LED” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte28RFL LC11 – Dimmwert AB28”

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
Select “127” and confirm.

L’article Touran (2T) – Delete LED reversing light bulb error est apparu en premier sur VAG Coding.

Purpose: removes the ODB error after installation of LED fog lamps.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Lasttyp 12”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Dimmwert AB 12”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Lasttyp 13”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Dimmwert AB 13”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

L’article Ateca (5F) – Delete LED fog lamp error est apparu en premier sur VAG Coding.

Purpose: removes the ODB error after installation of LED fog lamps.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Lasttyp 12”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Dimmwert AB 12”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Lasttyp 13”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Dimmwert AB 13”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

L’article Tiguan 2 (AD1) – Delete LED fog lamp error est apparu en premier sur VAG Coding.

Purpose: removes the ODB error after installation of LED fog lamps.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Lasttyp 12”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Dimmwert AB 12”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Lasttyp 13”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Dimmwert AB 13”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

L’article Touran (2T) – Delete LED fog lamp error est apparu en premier sur VAG Coding.

Purpose: Eliminates ODB error after LED reversing light installation.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64 – Lasttyp 29”.

7 – On the same page, there is a second drop-down menu at the bottom
of the page.
Select“43 – allgemeine LED” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64 – Dimmwert AB29”

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose “127” then validate.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte28RFL LC11 – Lasttyp 28”.

7 – On the same page, there is a second drop-down menu at the bottom
of the page.
Select“43 – allgemeine LED” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte28RFL LC11 – Dimmwert AB28”

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
Select “127” and confirm.

L’article Octavia 3 (5E) – Delete LED reversing light bulb error est apparu en premier sur VAG Coding.

Purpose: Eliminates ODB error after LED reversing light installation.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64 – Lasttyp 29”.

7 – On the same page, there is a second drop-down menu at the bottom
of the page.
Select“43 – allgemeine LED” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64 – Dimmwert AB29”

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose “127” then validate.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte28RFL LC11 – Lasttyp 28”.

7 – On the same page, there is a second drop-down menu at the bottom
of the page.
Select“43 – allgemeine LED” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte28RFL LC11 – Dimmwert AB28”

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
Select “127” and confirm.

L’article Passat (B8) – Delete LED reversing light bulb error est apparu en premier sur VAG Coding.

Purpose: removes the ODB error after installation of LED fog lamps.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Lasttyp 12”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12 NL LB45-Dimmwert AB 12”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Lasttyp 13”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“6 LED Lichtmodul” and confirm. (source: 10 – allgemeine Scheinwerfer)

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13 NL RB5-Dimmwert AB 13”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“127” and confirm. (origin : 100)

L’article Leon (5F) – Delete LED fog lamp error est apparu en premier sur VAG Coding.