Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article Octavia 4 (NX) – Enable Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article Formentor (KM7) – Activate Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article Leon 4 (KL) – Activate Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article A3 (8Y) – Enable Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the rearview camera after it has been installed on the MIB (retrofit).


SFD: Yes

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program or the OBDeleven app.

Hardware upgrade :

VW Retrofit Kit: 5H9 054 634

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click “Coding – 07,” then click “Long Coding Helper“

5 – Select the bit: PaCo_Video_Parksystem – RVC_compact_smart

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car Function List BAP – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “can_fas“

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_unit– RVC_video_input“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “ethernet“

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “parkingsystem_video_input– carrier_resolution“

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select the value “1392×656“

Line 6:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc – rvc_low_black_screen_trunk_open“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 7:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_failsafe“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 8:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_black_screen_velocity_threshold“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 9:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rear_view_low_rvc“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “not_active“

Line 10:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_lid_close_delay_time“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select the value “0 [ONE]_s“

Line 11:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “function_configuration_rvc– rvc_low_videofailure_detection_time“

7 – On this same page, there is a second drop-down menu, but further down
.
From this menu, select the value “0“

L’article Golf 8 (5H) – Enable Rearview Camera (Retrofit) est apparu en premier sur VAG Coding.

Purpose: Selects the speed at which the radar and/or reversing camera are deactivated.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“76 – Assistance stationnt“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Switch-off speed for parking assist“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“15” km/h, depending on your preference.

L’article Born (K11) – Speed of radar (or reversing camera) deactivation est apparu en premier sur VAG Coding.

Purpose: Selects the speed at which the radar and/or reversing camera are deactivated.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“76 – Assistance stationnt“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Switch-off speed for parking assist“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“15” km/h, depending on your preference.

L’article Enyaq (NY) – Radar deactivation speed (or rearview camera) est apparu en premier sur VAG Coding.

Purpose: Selects the speed at which the radar and/or reversing camera are deactivated.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“76 – Assistance stationnt“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Switch-off speed for parking assist“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“15” km/h, depending on your preference.

L’article ID.4 (E2) – Speed of radar (or reversing camera) deactivation est apparu en premier sur VAG Coding.

Purpose: Selects the speed at which the radar and/or reversing camera are deactivated.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“76 – Assistance stationnt“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Switch-off speed for parking assist“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“15” km/h, depending on your preference.

L’article ID.3 (E1) – Speed of radar (or reversing camera) deactivation est apparu en premier sur VAG Coding.

Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Car Function List BAP Gen2 – VPS_0x0B_msg_bus“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “Terminal 15“

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article A7 (C7) – Activate reversing camera (retrofit) est apparu en premier sur VAG Coding.