Purpose: to activate fog lamps when reversing.

Watch out! There are 4 lines of coding to do here.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12NL LB45-Lichtfunktion C 12“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Rueckfahrlicht” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12NL LB45-DimmwertCD12“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“100” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13NL RB5-Lichtfunktion C 13“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Rueckfahrlicht” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13NL RB5-DimmwertCD13“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“100” and confirm.

D12 and D13 if C12 and C13 are already active, 127 instead of 100 if you have LED ABs.

INFO: Impossible to code with a Golf 7R or GTE (no AB) or a Golf without AB!

L’article Golf 7 (5G) – Activate fog lamps when reversing est apparu en premier sur VAG Coding.

Purpose: to increase the intensity of door lighting.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte16BLK SLB35BLK SL KC9-Dimmwert AB 16”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte17TFL R BLK SRB3TFL R SR KC3-Dimmwert AB 17”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

L’article Golf 7 (5G) – Increase door lighting intensity est apparu en premier sur VAG Coding.

Purpose: to provide headlight flashes with the reversing lights (to warn drivers who are too close to you).

Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte28RFL LC11-Lichtfunktion B 28“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Lichthupe generell” and confirm.

Line 2 (Option to increase the intensity of the reversing light) :

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte28RFL LC11-Dimmwert AB 28”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, select“100” for Halogens or“127” for LEDs, then confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64-Lichtfunktion B 29“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Lichthupe generell” and confirm.

Line 4 (Option to increase the intensity of the reversing light) :

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte29RFL RA64-Dimmwert AB 29”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, select“100” for Halogens or“127” for LEDs, then confirm.

L’article Golf 7 (5G) – Headlamp call with reversing lights est apparu en premier sur VAG Coding.

Purpose: activates rearview mirror defrosting automatically when rear window defrosting is activated, to avoid having to move the rearview mirror switch to set defrosting, for example when in position R for reversing.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“: “Rear window heater trigger, active“


Line 2:

3 – Click on“Select”, then click on“42 – Driver’s door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“:“Rear window heater trigger, active“.

L’article Golf 7 (5G) – Activate automatic mirror defrosting with rear window est apparu en premier sur VAG Coding.

Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-side activation via the turn signal switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Außenlicht_uebergreifend-Parklicht ueber LSS aktiviert”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Bilateral” and confirm.

L’article Golf 7 (5G) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: to adjust the logic of the AWD system to increase traction or reduce noise generated by the Haldex AWD mechanism. (For Golf 7 4Motion / Golf 7R)

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“22 – AWD”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Logique” /“Logic”.

6 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On this, choose the value according to your preference:

• “Standard”
• “Increased Traction
• “Less Noise

then validate.

L’article Golf 7 (5G) – Haldex traction control est apparu en premier sur VAG Coding.

Purpose: To modify and customize ODB with a particle / checkerboard effect.

Information: Compatible with Golf 7 GTI / GTE / Clubsport / 7R (phase 1 from 2016) and all Golf 7 facelifts with needle counter on ODB display!


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on ” Select”, then click on ” 17- Instruments “.

4 – Click on ” Adaptation – 10 “.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the channel ” Displaydarstellung or Layout ” / ” Présentation or Affichage ” / “Display Depiction”.

6 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Version 3” and confirm.

If your meter is not compatible (before 2016), select “Version 2” for ODB Carbone :

For Golf 7.5 Facelift :

L’article Golf 7 (5G) – Particle-effect display on ODB est apparu en premier sur VAG Coding.

Purpose: to activate the two rear fog lamps. (originally only one is activated)

On French and German models, this option cannot be activated without hardware modification.
– Either replace the right rear complete block with an English model. (Mandatory for LED lights)
– Either cut out the fog lamp slot in the existing block and add the bulb.

Watch out! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte26NSL LA72-Lichtfunktion A 26”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, choose“Nebelschlusslicht wenn kein Anhaenger gesteckt” then confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then click on“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte27NSL RC6-Lichtfunktion A 27”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, choose“Nebelschlusslicht wenn kein Anhaenger gesteckt” then confirm.

L’article Golf 7 (5G) – Activation of both rear fog lamps est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Golf 7.5 (5G) Facelift – Front Assist settings est apparu en premier sur VAG Coding.

Purpose: deactivates sound reduction when reverse gear is engaged or parking aid is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Demande réduction audio ” / “Audio attenuation request” / “Anforderung Audioabsenkung ” from the value list.

7 – Select “Off” in the second value list

L’article Golf 7 (5G) – Disable audio reduction for parking aid est apparu en premier sur VAG Coding.