Purpose: Enables the “ECOTRAINER” mode: Displays the “ECO MODE” graph on the MIB2.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_user_eco_rating”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_user_eco_rating_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

L’article Ibiza (6P) – Enable “EcoTrainer” mode est apparu en premier sur VAG Coding.

Purpose: Allows you to add Apple CarPlay and Android Auto to Full Link after it has been enabled on MIB2 systems with 2xxT part numbers, when only MirrorLink appears in the Full Link menu.

For the firmware reference:
MST2_EU_SE_ZR_P02XXT

–> Full Link CarPlay and Android Auto Activation
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Ibiza (6P) – Add CarPlay / Android Auto after activating Full Link MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Allows you to disable or remove MirrorLink from Full Link on the MIB2. The MirrorLink service has not been natively available on Android since June 1, 2020. For a direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Ibiza (6P) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: to lock/unlock the CD/DVD eject button on the MMI.

Protection against CD theft.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on“5F – Information Electr.“. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on ” Adaptation – 10 “.

5 – Select “Ejector lock / “Auswurfssperre / “CD Eject Button then set the value to Active for eject lock.

To eject the CD/DVD, set the value to Off for normal use of the button.

L’article Ibiza (6P) – Lock CD/DVD eject button est apparu en premier sur VAG Coding.

Purpose: Allows you to use the key and lock the vehicle with the ignition switched on or the engine running. (Very practical with a Keyless Kessy key)

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access control-Funk bei Klemme 15 ein”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Ibiza (6P) – Key operation with ignition on est apparu en premier sur VAG Coding.

Purpose: to adjust the intensity of brake disc drying. If your car has a tendency to squeal when parked in wet weather, for example, the annoying drying of disc brakes can be reduced or even completely deactivated, so that there are no more scratches or squeaks.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“03- Electronic brakes”.

4 – Click on“Security Access – 16” then enter the code“40304”.

5 – Click on“Adaptation – 10“.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“brake disc drying“

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose the value accordingly to your choice: ” not activated, low, medium, high ” then validate.

L’article Ibiza (6P) – Brake disc drying est apparu en premier sur VAG Coding.

Purpose: activates the brake/turn signal lights in flash mode during emergency braking.

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Aussenlicht_Blinker – Emergency alert blinken”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Active” and confirm.

OR

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 16:
Bit 1: Check “Emergency Brake Flashing via Brake Light active” (to activate brake lights)
Bit 2: Check “Emergency Brake Flashing via Turn Signal active” (to activate turn signals)

L’article Ibiza (6P) – Flash mode lights during emergency braking est apparu en premier sur VAG Coding.

Purpose: to disable the AM radio frequency on the display (AM radio frequency is rarely used, unlike FM radio frequency).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 14

Set bit 1 “AM_disable

L’article Ibiza (6P) – Disable AM frequency est apparu en premier sur VAG Coding.

Purpose: deactivates or activates the horn when the ignition is off.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Additional functions – Signalhorn ohne KL 15”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, choose“not active” to deactivate it or “active” to activate it, then confirm.

L’article Ibiza (6P) – Disable horn without ignition est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop completely.

Watch out! There are 1 or 2 lines of coding to do here, depending on the method.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Method 1 (voltage method, recommended):

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Limite de tension de départ marche/arrêt” / “Start/Stop voltage limit”.

6 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“12” (default value = 7.6V) then validate.

OBDeleven:

YouTube video:

Method 2 (Temperature method):

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Minimaltemperatur”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“50” (default value = -50.0) and confirm.

Line 2:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Maximaltemperatur”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“50” (default value = -50.0) and confirm.

OBDeleven:

L’article Ibiza (6P) – Start/Stop deactivation est apparu en premier sur VAG Coding.