Purpose: Allows you to add Apple CarPlay and Android Auto to Full Link after it has been enabled on MIB2 systems with 2xxT part numbers, when only MirrorLink appears in the Full Link menu.

For the firmware reference:
MST2_EU_SE_ZR_P02XXT

–> Full Link CarPlay and Android Auto Activation
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Toledo (NH) – Add CarPlay / Android Auto after activating Full Link MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Allows you to disable or remove MirrorLink from Full Link on the MIB. The MirrorLink service has not been natively available on Android since June 1, 2020. For a direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Toledo (NH) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: to disable the AM radio frequency on the display (AM radio frequency is rarely used, unlike FM radio frequency).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 14

Set bit 1 “AM_disable

L’article Toledo (NH) – Deactivate AM frequency est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to the Easy Connect MIB V2 screen with navigation.


Watch out! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Additional line if OFF Road not activated :

Car_Function_Adaptations_Gen2

menu_display_compass: change the value to “activated” [Standard: “Not activated”]
menu_display_compass_over_therhold_high: change the value to “activated” [Standard: “Not activated”]
menu_display_angle_of_slope: change the value to “activated” [Standard: “Not activated”]
menu_display_angle_of_slope_over_threshold_high: change the value to “activated” [Standard: “Not activated”]

Car_Function_List_Bap_Gen2

compass_0x15: change the value to “activated” [Standard: “Not activated”]
compass_0x15_msg_bus: change the value to “Comfort data bus”
angle_of_slope_0x24: change the value to “activated” [Standard: “Not activated”]
angle_of_slope_0x24_msg_bus: change the value on “Comfort data bus”

L’article Toledo (NH) – Activate Off-Road mode est apparu en premier sur VAG Coding.

Purpose: Adds a driving-school mode view to Easy Connect, displaying turn signals, speed, etc. (also ideal for accompanied driving).


Watch out! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list CAN-Driving_school“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_driving_school“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_driving_school_over_threshold_high“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Toledo (NH) – Activate driving-school mode est apparu en premier sur VAG Coding.

Purpose: Enables the USB port for iPhone CarPlay accounting (after Full Link activation and USB and/or USB cable change) for MIB2 (Retrofit).

For firmware references:
MST2_EU_SE_ZR_P02XXT (before 2016)

Modify the MIB2 coding and adaptation to recognize the new USB port (USB connector ref 5Q0 035 726 E) for both CarPlay and USB multimedia playback. A coding pin on the connector needs to be modified.

–> Full Link CarPlay and Android Auto Activation
–> VW Golf 7 USB/AUX Port for CarPlay Media MIB2 5Q0 035 726 E on VAG Custom
–> Adding CarPlay / Android Auto after activating Full Link MIB2 2xxT
–> Disable MirrorLink


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Codage- 07” then click on“Assistant Codage Long”.

5 – Select byte“19“
Then check Bit“6-7” (C0 USB Configuration: USB and iPhone Functionality)

Line 2 (optional) :

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interface for external media activation – connection 1“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “activated“

L’article Toledo (NH) – Activate USB port for iPhone CarPlay (retrofit) est apparu en premier sur VAG Coding.

Purpose: Activates the green hidden menu (green menu, hidden menu, testmode, engineer mode) on MIB2.

/!\ Caution: Making certain changes in the hidden menu may cause MIB2 to freeze or no longer start /!\


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“S12345“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Developer mode“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value“activated“.

Restart MIB2, keep MENU button pressed until testmode menu appears

L’article Toledo (NH) – Activate hidden menu est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Toledo (NH) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for Seat Toledo (NH)
–> Buy your OBDeleven device with VAG Custom

Seat Toledo NH (2012-2019)

2012-2015 :

• Inspection service reset
• MirrorLink on the move
• Oil service reset
• Video in motion
• Acoustic lock confirmation
• CTS activation/deactivation
• Automatic locking/unlocking
• Automatic tailgate locking/unlocking
• Central lock settings
• CH/LH lights
• Comfort flashing light
• Time to return home
• Country setting for horn
• Emergency brake lights
• Front wiper operating mode/position
• Headlamp washer
• Tilt sensor sensitivity
• Sensitivity of interior surveillance
• Home departure time
• Parking lights
• Wiping the reverse gear
• Static bend lights
• Teardrop wipe
• Visual confirmation of comfort operation
• Visual confirmation
• Motor 1 fan test
• Motor 2 fan test
• Engine oil type
• Inspection service distance
• Inspection service interval
• Oil change service distance
• Oil change service interval

2015-2019 :

• Central locking with IGN
• CH/LH light function
• DRL parameters in main unit
• DRL disabled with handbrake
• Gauge test – Needle sweep
• Headlamp washer
• Basic headlight settings
• High-intensity brake light
• Hill-start assist
• Inspection service reset
• Stopwatch
• Acoustic confirmation of locking/unlocking
• MirrorLink on the move
• Oil service reset
• Oil temperature in DIS
• Open door alarm
• Optical parking system
• Fuel quantity in instrument panel
• Trunk release/remote trunk release
• Scandinavian DRL
• Disabling the Start/Stop system
• Static bend lights
• Video in motion
• Remote Windows function
• Battery capacity
• Battery type
• Brake light test
• Door lock test all
• Motor fan test
• Engine oil type
• Left front door lock test
• Right front door interlock test
• Headlamp washer test
• Inspection service distance
• Inspection service interval
• Multimedia security disclaimer
• Oil change service distance
• Oil change service Interval
• Left rear door lock test
• Right rear door lock test
• Back-up light test
• Warning of impending maintenance
• Turn signal test

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article List OBDeleven One-Click Apps TOLEDO (NH) est apparu en premier sur VAG Coding.

Purpose: to set automatic door unlocking when the vehicle has been unlocked but no doors have been opened for 30 seconds.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 4:
Bit 5: Uncheck “Central Locking Re-locking (after 30 seconds) active”.

L’article Toledo (NH) – Automatic door locking after 30s est apparu en premier sur VAG Coding.