Purpose: automatically lowers the passenger mirror when reversing.

The mirror adjustment knob must be in position“R” for the passenger mirror to lower automatically.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “09 – Centrale Elec”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – In the window that appears, select byte 4 and check bit 3 “ Mirror Lowering With Reverse Rear ” to activate mirror lowering when shifting into reverse gear:

6 – After this operation, click on the “Output” menu, then validate “OK”.

A message appears to inform you that the coding has been accepted.

Line 2:

3 – Click on “Select” , then click on “52 – Passenger door”.

4 – Click on “Coding – 07”.

Add 256 to the value

L’article Altea (5P) Facelift – Lowering the passenger mirror when reversing est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after installation on the RCD 510/330/360/440 and RNS 315/510 (retrofit).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 3
Then check bit 6 “Rear View Camera (RVC) installed/active”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Assistance Stationn”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 0
Then check bit 5 “Rear View Camera installed”.

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Altea (5P) Facelift – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Altea (5P) Facelift – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Altea (5P) Facelift – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: To suppress the audible alarm and the warning light on the speedometer when driving without a seatbelt.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 1: “Seatbelt warning active/installed”.

L’article Altea (5P) Facelift – Remove alarm belt est apparu en premier sur VAG Coding.

Purpose: to activate voice control on the RNS 510 (SDS).

ATTENTION: RNS 510 firmware must be version v2660.

Activating voice control brings up the “Voice control” menu in the RNS 510’s SETUP menu.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3, check the box for“Bit 1: Microphone Diagnostics active”.

Byte 7, uncheck the box for“Bit 1: Voice Control inactive”.

To install the microphone, connect the microphone lead to the rear of the RNS 510. Connect to pins (Mic-)C1 and (Mic+)C7.

L’article Altea (5P) Facelift – Activate RNS 510 voice command est apparu en premier sur VAG Coding.

Purpose: Allows you to add a Driving School mode view to the RCD 210, RCD 310 that displays turn signals, speed … (Also ideal for accompanied driving)


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“56 – Radio”.

4 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Channel 2”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“1” and confirm.

L’article Altea (5P) – Activate Driving School mode (RCD 210/RCD 310) est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for Seat Altea (5P)
–> Buy your OBDeleven device with VAG Custom

Seat Altea 5P (2004-2015) / Seat Altea XL / Altea 5P Facelift (specific facelift coding at bottom of page)

• Activate Bluetooth RNS315
• Bending lights
• Daytime running lights
• DRL parameters
• ESC V2 deactivation
• Heating test
• Unlocking the heater
• Oil service reset
• PTT button options
• CD lock RNS 310/315
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 SDS reversing camera
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• Speed limit RNS 510
• RNS 510 theme
• Automatic locking/unlocking
• Brake pad warning
• Central locking with IGN
• Comfort windows
• Take-home mode
• Time to return home
• Emergency brake lights
• Floor lighting
• Floor lighting while driving
• Brightness of front parking lights
• Headlamp washer
• Instrument cluster language
• Home departure time
• Deactivation of rear fog lights
• Seat belt warning
• Selective Central locking
• Brightness of rear lights
• American-style turn signals
• Self-closing windows
• Engine oil type

Seat Altea 5P Facelift (2009-2015)

• Activate Bluetooth RNS315
• Automatically folding mirrors
• ESC V2 deactivation
• Heating test
• Unlocking the heater
• Inspection service reset
• Oil service reset
• PTT button options
• CD lock RNS 310/315
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 reversing camera
• SDS RNS 310/315
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• RNS 510 theme
• Automatic rear lid lock
• Brake lights with ignition
• Central locking
• CH light mode
• CH light timer function
• CH/LH lights
• CH/LH lights via dipped beam/fog lights
• Comfortable flashing
• Comfortable opening type for sunroof
• Convenient operation for driver’s window
• Convenient operation for sunroofs
• Convenient window operation with door locks
• Bending lights
• Timer alarm Activation
• Daytime running lights inactive when indicators are active
• Emergency brake lights
• Rear wiper activation with reverse gear
• Fog lamps as daytime running lights
• Gauge test – Needle sweep
• Headlight dimming
• Headlights for right/left-hand traffic
• Instrument cluster country version
• Instrument cluster language
• LED license plate illumination
• Turn signal lock/unlock confirmation
• Locking/unlocking confirmation – Horn
• Multifunction display
• Parking lights off when ignition is switched off
• Permanent position lights
• Electrically folding mirrors
• Rear fog lights off when main beam is on
• Seat belt warning
• Rear light dimming
• Visual confirmation for convenient operation
• Windows/sunroof with contact
• Engine oil type
• Inspection service distance
• Inspection service interval
• Oil change service distance
• Oil change service interval

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps ALTEA list (5P) est apparu en premier sur VAG Coding.

Purpose: locks/unlocks the RNS 510’s CD/DVD eject button.

Protection against theft of your navigation DVD.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” Select ” and run the VCDS program. 37 – Navigation” .

4 – Click on “Adaptation – 10”.

5 – Select Channel 43 (Ejection Lock) then set the value to 1 (CD/DVD Ejection Lock active)

Restart the RNS 510.

L’article Altea (5P) Facelift – Lock the CD/DVD eject button on the RNS 510 est apparu en premier sur VAG Coding.

Purpose: to change the display theme of the RCD 510 and RNS 510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” for RNS510 and “56 – Radio” for RCD510.

4 – Click on“Coding 07” then “Long Coding Helper”.

5 – Select Byte 7

Bit 4-5: Select from 3 themes
“00 Display Variant: Highline
“10 Display Variant: Sportsline
“20 Display Variant: Premium

Exit the module and save your changes. The RCD / RNS 510 must now be restarted for the changes to take effect. Press both arrows and the star for 6s.

L’article Altea (5P) Facelift – Changing the RCD/RNS 510 theme est apparu en premier sur VAG Coding.