Purpose : to activate GRA cruise control (retrofit).

Modification only possible after retrofit of cruise control switch.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select “, then click on “Select”. 01 – Engine ” .

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte“5“
Select bit“5-6” 20 Cruise Control System (CCS) installed

Line 2:

3 – Click on ” Select ” then click on ” 16 – Multifunction steering wheel ” .

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte“5“
Select bit“4-7” 20 Cruise Control controlled via Separate Lever

L’article Q3 (8U) – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.

Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 5 = video line
Pin 11 = shielding

L’article Q3 (8U) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to set the distance between the kerb and the car during Audi Park Assist.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“10 – Park/Steer Assist”/ “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Abstand zum Bordstein” / “Distance to curb” / “Ecart avec la bordure”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the distance you prefer (in cm). Default value“15cm” then validate.

L’article Q3 (8U) – Increase distance between curb and car (Park Assist) est apparu en premier sur VAG Coding.

Purpose: Activates battery charge status in Audi MMI 3GP.

WARNING: You must have activated the Hidden Menu(Activate MMI 3GP hidden menu).

To launch the Hidden Menu press MENU + CAR (for 6s)

car -> carextdevicelist -> battery -> check box

car -> carmenuoperation -> battery -> select 5

Restart MMI

Press SETUP + Wheel + Top Right Button.

L’article Q3 (8U) Facelift – Activate battery charge status in MMI est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Q3 (8U) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Q3 (8U) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for Audi Q3 (8U)
–> Buy your OBDeleven device with VAG Custom

Audi Q3 8U (2011-2018) / Audi RSQ3 / Q3 8U Facelift / (specific facelift coding at bottom of page)

• Automatic wiper in reverse
• Basic transmission settings
• Brake pad wear indicator
• Brake pad replacement
• Central locking with IGN
• Comfort turn signals
• Comfort windows
• Time to return home
• Bending lights
• Bending lights with reverse
• DRL function with flashing light
• DRL settings in main unit
• DRL with ADL
• DRL with handbrake on
• MMI 3G DVD lock
• Dynamic steering recommendation
• Flashes emergency brake with trailer
• Emergency brake lights
• 3G/3G+ technical menu
• RMC technical menu
• Fog lamps with high beam
• Folding mirrors
• Floor lighting
• Gauge test – Needle sweep
• Headlamp washer
• Basic headlight settings
• Freeway lights
• Hill-start assist
• Hill-start assist settings
• Inspection service reset
• Departure time
• LED license plate lamps
• Acoustic confirmation of locking/unlocking
• Mirror scan
• MMI 3G/3GP radio frequency
• MMI 3G/3GP video input Movement
• Oil service reset
• Rain lights
• Rear cover control
• Rear window wiper
• RMC repair
• Seat belt warning
• Summer menu in MMI
• Drop-shaped wiping
• Back drop wiping
• TSC
• Moving video for RMC
• Washer fluid indicator
• Window and mirror heater activation time
• CH/LH lights
• CH/LH light variant
• CH/LH via LED DRL
• DRL activation/deactivation
• Motor fan test
• Fuel system priming
• Optical parking system
• Repair RMC Languages EU
• Engine oil type
• Inspection service distance
• Inspection service interval
• Oil change service distance
• Oil change service interval
• Repair RMC Languages EU Version 2
• Repair RMC Languages USA
• Disabling the Start/Stop system

Audi Q3 8U Facelift (2015-2018)

• Automatic wiper in reverse
• Basic transmission settings
• Brake pad wear indicator
• Brake pad replacement
• Central locking with IGN
• Comfort turn signals
• Comfort windows
• Time to return home
• Bending lights
• Bending lights with reverse
• DRL function with flashing light
• DRL settings in main unit
• DRL with ADL
• DRL with handbrake on
• MMI 3G DVD lock
• Dynamic steering recommendation
• Flashes emergency brake with trailer
• Emergency brake lights
• 3G/3G+ technical menu
• RMC technical menu
• Fog lamps with high beam
• Folding mirrors
• Floor lighting
• Gauge test – Needle sweep
• Headlamp washer
• Basic headlight settings
• Hill-start assist
• Hill-start assist settings
• Inspection service reset
• Departure time
• LED license plate illumination
• Acoustic confirmation of locking/unlocking
• Mirror scanning
• MMI 3G/3GP radio frequency
• Oil service reset
• Rain lights
• Rear cover control
• Rear Wiper
• Seat belt warning
• Teardrop wipe
• Rear teardrop wiper
• TSC
• Moving video for RMC
• Washer fluid indicator
• Window and mirror heater activation time
• Daytime running lights on/off
• Fuel system priming
• MMI 3G/3GP motion video
• RMC repair EU languages
• Summer menu in MMI
• Engine oil type
• Inspection service distance
• Inspection service interval
• Oil change service distance
• Oil change service interval

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps Q3 (8U) list est apparu en premier sur VAG Coding.

Purpose: To modify and/or customize the home screen logo (Custom Splash Screen) with a personalized image of the MMI 3G and 3GPLUS.

Start by downloading the script file: MMI_3G_3GP_SplashScreen_VAG-Coding.en.zip

Proceed :

• Then extract the file you just downloaded: MMI 3G 3GP SplashScreen VAG-Coding.en.zip
• Go to the “splashscreens” folder and edit the “startup_generic.png” image if you wish. You can edit this image, modify it or import another image, to have your own startup logo (keep the same PNG format and image size 800×480) or an image found in the “samples” folder (copy it into the “splashscreens” folder with the name startup_generic.png.
• Copy the contents of the MMI_3G_3GP_SplashScreen folder to a FAT32-formatted SD card (max. 32GB).
• Start your AUDI and let the MMI boot up, it takes a few seconds.
• Disconnect your smartphone’s Bluetooth if there’s a link between it and the MMI, and remove all your SD cards (SD1 & SD2)…
• Then insert the SD card you have prepared into slot SD1.
• You’ll see green text asking you to turn the large knob on your MMI central console, and the message will disappear.
• Wait a few moments. A new message will appear stating that all has gone well and that your image has been imported successfully.
• Restart the MMI using the button combination that corresponds to your AUDI.
  Example: Press SETUP or MENU (1) + Central knob (2) + Top right button (3) at the same time.

If your new start-up screen does not appear when your MMI reboots, go to the green hidden menu (to activate the hidden menu, follow the “Activate MMI 3G or 3GP hidden menu” tutorial).

For MMI 3GP : Select in car -> carcodingvehicle -> Select n° screen -> set cursor to 0, then restart your MMI.

For MMI 3G: car -> carcodingvehicle -> configuration line -> [standard] 2/5 (Standard home screen) then restart your MMI.

Your very own Splash Screen will appear!
Many images are available in the zip file… both the original and modified ones.

A problem? If the script doesn’t run the first time, try again. You’ve only copied the contents of the MMI_3G_3GP_SplashScreen folder? Do not copy the folder, just its contents!
For MMI 3G Basic: If your image does not appear or is truncated, resize the image to 400 by 240.

L’article Q3 (8U) Facelift – MMI 3G/3GP customized start logo est apparu en premier sur VAG Coding.

Purpose: to deactivate/activate the electric handbrake in maintenance mode in order to change/replace the rear brake pad/disc linings. (EPB reset / Lining change mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


To start, set the gear lever to P, remove the electric handbrake on the button and preferably connect a battery charger according to the vehicle manual. Check that there are no faults/errors before starting basic setup.

3 – Click on“Select” then click on“53 – Parking Brake”.

4 – Click on“Basic setting – 04”.

5 – Select Channel 007

6 – Click on“Go”.

Basic Settings: OFF during the procedure, then ON when finished (yellow arrow).

A fault message will appear on your ODB indicating“Parking brake fault” and an LED in the parking brake switch, but this is normal and should be ignored.

7 – Once finished, go back (Done, Go Back) until the program closes.

8 – Switch off the vehicle’s ignition, then disconnect the VAG-COM cable

9 – Change the linings on both sides!

To reactivate the electric handbrake :


10 – With engine off and ignition switched off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

11 – Switch on the ignition and run the VCDS program.

12 – Click on“Select” then click on“53 – Parking Brake”.

13 – Click on“Basic setting – 04”.

14 – Select Channel 006

15 – Click on“Go”.

Basic Settings: OFF during the procedure, then ON when finished (yellow arrow).

16 – Once finished, go back (Done, Go Back) until the program is closed.

17 – Switch off the ignition and disconnect the VAG-COM cable.

L’article Q3 (8U) – Deactivate/activate electric handbrake for rear brake pad change est apparu en premier sur VAG Coding.

Purpose : to activate Audi Auto-Hold Assist (retrofit).

Keeps the vehicle stationary on slopes and downhill gradients for as long as required. If the vehicle remains stationary for a long time, the system automatically switches to electromechanical braking.

Part 8U0-927-225-E (former version 8U0-927-225-C) must be ordered and installed before coding.

Before activation with VCDS, stop the vehicle on level ground and disengage the electric handbrake

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“53 – Parking Brake”.

4 – Click on“Codage- 07” then“Long Coding Helper”.

5 – Replace value: xxxxxx6 by xxxxxx7

L’article Q3 (8U) – Activate Auto-Hold Assist (retrofit) est apparu en premier sur VAG Coding.