Purpose: To activate the reversing camera after it has been installed on the MMI RMC or 3GP.


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway“.

4 – Select “Installation List”

5 – Tick:“6C – Rear View Camera” in the list

6 – Save coding

Line 2:

3 – Click on“Select” then click on“6C – Rear view camera“.

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Coding:

1030015 = Automatic hitch, with APS+.

1000015 = RVC only

1020015 = APS+, without automatic coupler

1010015 = Automatic hitch, without APS+.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper“.

For MMI RMC :
6 – Select byte 6
Then set bit 2

For MMI 3GP:
6 – Select byte 7
Then set bit 1

Restart MMI

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. This is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 5 = video line
Pin 11 = shielding

L’article A1 (8X) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the efficiency indicator to be displayed on the ODB (On Board Computer) for an efficient, environmentally-friendly driving style.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then check Bit 7: “Bodycomputer”.

L’article A1 (8X) – ODB efficiency indicator display est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the on-board computer.

Note: these changes affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel: “Display correction of consumptions and operating range”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96.

Example 3: the consumption announced by the ODB is 5.9l/100km, after checking it is actually 6.3l/100km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%, and the consumption announced by the ODB will be a pessimistic 0.1l/100km.

Consumption is immediately modified on the MMI.

L’article A1 (8X) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop completely.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“26”
Then uncheck Bit“0”.

Line 2:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Indicateur pour fonctionnement start-stop” /“Control lamp for start-stop operation”.

6 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Deactivate” and confirm.

L’article A1 (8X) – Start/Stop deactivation est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article A1 (8X) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article A1 (8X) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Audi A1 (8X)
–> Buy your OBDeleven device with VAG Custom

Audi A1 8X (2010-2018) / Audi S1 / A1 8X Facelift (specific facelift coding at bottom of page)

• Automatic wiper in reverse
• Brake pad wear indicator
• Central locking with IGN
• Comfort turn signals
• Comfort windows
• Time to return home
• Bending lights
• Bending lights with reverse
• DRL function with flashing light
• DRL settings in main unit
• DRL with ADL
• DRL with handbrake on
• MMI 3G DVD lock
• Flashes emergency brake with trailer
• Emergency brake lights
• 3G/3G+ technical menu
• RMC technical menu
• Fog lamps with high beam
• Folding mirrors
• Floor lighting
• Gauge test – Needle sweep
• Headlamp washer
• Basic headlight settings
• Hill-start assist
• Hill-start assist settings
• Inspection service reset
• Departure time
• LED license plate illumination
• Acoustic confirmation of locking/unlocking
• MMI 3G/3GP radio frequency
• MMI 3G/3GP video on the move
• Oil service reset
• Old BAP optical parking system
• Rain lights
• Rear window wiper
• Seat belt warning
• Soundaktor
• Summer menu in MMI
• Teardrop wipe
• Rear teardrop wiper
• Moving video for RMC
• Washer fluid indicator
• Window and mirror heater activation time
• CH/LH via LED DRL
• DRL activation/deactivation
• DRL menu in MMI
• Motor 1 fan test
• Motor 2 fan test
• Fuel system priming
• Mirror scan
• RMC fix Languages EU
• Engine oil type
• Inspection service distance
• Inspection service interval
• Oil change service distance
• Oil change service interval

Audi A1 8X Facelift (2014-2018)

• Automatic wiper in reverse
• Brake pad wear indicator
• Central locking with IGN
• Comfort turn signals
• Comfort windows
• Time to return home
• Bending lights
• Bending lights with reverse
• DRL function with flashing light
• DRL settings in main unit
• DRL with ADL
• DRL with handbrake on
• MMI 3G DVD lock
• Flashes emergency brake with trailer
• Emergency brake lights
• 3G/3G+ technical menu
• RMC technical menu
• Fog lamps with high beam
• Folding mirrors
• Floor lighting
• Gauge test – Needle sweep
• Headlamp washer
• Basic headlight settings
• Hill-start assist
• Inspection service reset
• Departure time
• LED license plate lamps
• Acoustic confirmation of locking/unlocking
• MMI 3G/3GP Radio frequency
• MMI 3G/3GP Video on the move
• Oil service reset
• Old BAP optical parking system
• Rain lights
• Rear window wiper
• Seat belt warning
• Soundaktor
• Summer menu in MMI
• Teardrop wipe
• Rear teardrop wiper
• Moving video for RMC
• Washer fluid indicator
• Daytime running lights on/off
• Motor fan test
• Fuel system priming
• RMC repair
• Engine oil type
• Inspection service distance
• Inspection service interval
• Mirror scan
• Oil change service distance
• Oil change service interval

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps A1 (8X) list est apparu en premier sur VAG Coding.

Purpose: To modify and/or customize the home screen logo (Custom Splash Screen) with a personalized image of the MMI 3G and 3GPLUS.

Start by downloading the script file: MMI_3G_3GP_SplashScreen_VAG-Coding.en.zip

Proceed :

• Then extract the file you just downloaded: MMI 3G 3GP SplashScreen VAG-Coding.en.zip
• Go to the “splashscreens” folder and edit the “startup_generic.png” image if you wish. You can edit this image, modify it or import another image, to have your own startup logo (keep the same PNG format and image size 800×480) or an image found in the “samples” folder (copy it into the “splashscreens” folder with the name startup_generic.png.
• Copy the contents of the MMI_3G_3GP_SplashScreen folder to a FAT32-formatted SD card (max. 32GB).
• Start your AUDI and let the MMI boot up, it takes a few seconds.
• Disconnect your smartphone’s Bluetooth if there’s a link between it and the MMI, and remove all your SD cards (SD1 & SD2)…
• Then insert the SD card you have prepared into slot SD1.
• You’ll see green text asking you to turn the large knob on your MMI central console, and the message will disappear.
• Wait a few moments. A new message will appear stating that all has gone well and that your image has been imported successfully.
• Restart the MMI using the button combination that corresponds to your AUDI.
  Example: Press SETUP or MENU (1) + Central knob (2) + Top right button (3) at the same time.

If your new start-up screen does not appear when your MMI reboots, go to the green hidden menu (to activate the hidden menu, follow the “Activate MMI 3G or 3GP hidden menu” tutorial).

For MMI 3GP : Select in car -> carcodingvehicle -> Select n° screen -> set cursor to 0, then restart your MMI.

For MMI 3G: car -> carcodingvehicle -> configuration line -> [standard] 2/5 (Standard home screen) then restart your MMI.

Your very own Splash Screen will appear!
Many images are available in the zip file… both the original and modified ones.

A problem? If the script doesn’t run the first time, try again. You’ve only copied the contents of the MMI_3G_3GP_SplashScreen folder? Do not copy the folder, just its contents!
For MMI 3G Basic: If your image does not appear or is truncated, resize the image to 400 by 240.

L’article A1 (8X) Facelift – MMI 3G/3GP customized start logo est apparu en premier sur VAG Coding.

Purpose: Activates CD/DVD extraction in the DVD player. Allows you to import / copy all CD/DVD / SD card content to the MMI 3G PLUS jukebox (hard disk).

To continue, you must first activate the hidden MMI menu (Green Menu).

To activate the MMI hidden menu (Green Menu) : Activate MMI 3GP hidden menu

Press CAR + SETUP for 6 sec to bring up the hidden menu.

diagnose -> settings -> import_multimedia -> Tick Ripping

Restart MMI

Press MENU + Wheel + Top Right button.

L’article A1 (8X) Facelift – Activate MMI 3GP CD/DVD extraction est apparu en premier sur VAG Coding.

Purpose: locks/unlocks the CD/DVD eject button on the MMI RMC.

Protection against CD theft.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on“5F – Information Electr.”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on “Adaptation – 10”.

5 – Choose Channel 10 then set the value to 1 for active eject lock.

Restart the MMI RMC.

To eject the CD/DVD, set the value to 0 for normal use of the button.

L’article A1 (8X) – Lock CD/DVD eject button on MMI RMC est apparu en premier sur VAG Coding.