Purpose: Allows you to correct the fuel consumption display on the On-Board Computer / Virtual Cockpit.

Note: The changes you make affect the display of instantaneous fuel consumption, average fuel consumption, and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “ Select,” then click “17 – Instruments.”

4 – Click “Adaptation – 10.”

5 – Select the Channel: “Display correction of consumption and operating range“

Set the consumption correction factor between 85% and 115% (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96 .

Example 3: The fuel consumption reported by the ODB is 5.9 L/100 km; after testing, it is actually 6.3 L/100 km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%; the fuel consumption figure reported by the ODB will be approximately 0.1 L/100 km too low.

The usage is immediately updated on the Discover MIB:

L’article Taigo (CS) – Fixed the OBD fuel consumption display est apparu en premier sur VAG Coding.

Purpose: Allows you to correct the fuel consumption display on the On-Board Computer / Virtual Cockpit.

Note: The changes you make affect the display of instantaneous fuel consumption, average fuel consumption, and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “ Select,” then click “17 – Instruments.”

4 – Click “Adaptation – 10.”

5 – Select the Channel: “Display correction of consumption and operating range“

Set the consumption correction factor between 85% and 115% (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96 .

Example 3: The fuel consumption reported by the ODB is 5.9 L/100 km; after testing, it is actually 6.3 L/100 km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%; the fuel consumption figure reported by the ODB will be approximately 0.1 L/100 km too low.

Consumption is immediately modified on the MMI.

L’article Q3 (F3) – Fixed the OBD fuel consumption display est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
Handy for instantly viewing the active profile without having to go through the multimedia menu. (Driving Mode / Drive Select)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Tiguan 2 (AD1) – Driving Mode via OBD est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
Handy for instantly viewing the active profile without having to go through the multimedia menu. (Driving Mode / Drive Select)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Ibiza (6F) – Driving Mode on OBD est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
Handy for instantly viewing the active profile without having to go through the multimedia menu. (Driving Mode / Drive Select)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Arteon (3H) – Driving Mode via OBD est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
Handy for instantly viewing the active profile without having to go through the multimedia menu. (Driving Mode / Drive Select)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Polo 6 (AW1) – Driving Mode on OBD est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
Handy for instantly viewing the active profile without having to go through the multimedia menu. (Driving Mode / Drive Select)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article T-Roc (A1) – Driving Mode via OBD est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
Handy for instantly viewing the active profile without having to go through the multimedia menu. (Driving Mode / Drive Select)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Karoq (NU) – Driving Mode on OBD est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
This is useful for instantly viewing the active profile without having to go through the multimedia menu. (Driving Mode / Drive Select)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Octavia 3 (5E) – Driving Mode on OBD est apparu en premier sur VAG Coding.

Purpose: Displays the intermediate km/h scale on the Virtual Cockpit speedometer. (Works only when the speedometer scale is set to km/h)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – instruments“.

4 – Click on“Coding – 07“, then on“Long Coding Helper“.

5 – Select byte “18“
. Then check bit “1“: “Tachometer_erweiterte_Skalenteilung”

OBDeleven: Tachometer_advanced_scale_division -> yes

L’article Q8 (4M) – Display intermediate speeds in the Virtual Cockpit est apparu en premier sur VAG Coding.