Purpose: to disable Start and Stop completely.

Watch out! There are 1 or 2 lines of coding to do here, depending on the method.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Method 1 (voltage method, recommended):

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Limite de tension de départ marche/arrêt” / “Start/Stop voltage limit”.

6 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“12” (default value = 7.6V) then validate.

OBDeleven:

YouTube video:

Method 2 (Temperature method):

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Minimaltemperatur”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“50” (default value = -50.0) and confirm.

Line 2:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Maximaltemperatur”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“50” (default value = -50.0) and confirm.

OBDeleven:

L’article Ibiza (6P) – Start/Stop deactivation est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop completely.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“26”
Then uncheck Bit“0”.

Line 2:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Indicateur pour fonctionnement start-stop” /“Control lamp for start-stop operation”.

6 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Deactivate” and confirm.

L’article A1 (8X) – Start/Stop deactivation est apparu en premier sur VAG Coding.

Purpose: to deactivate Start and Stop completely. For phase 1 and 2.



Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Phase 1 (2010/2016):

Only compatible with Gateway 7N0! Temperature deactivation method.

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on “Long Adaptation – 0A”.

5 – Select Channel“13

6 – In new value, select“D02000” (default value = 002000) then validate.

Phase 2 (Facelift) (2016/2022) :

Method 1 (voltage method, recommended):

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Limite de tension de départ marche/arrêt” / “Start/Stop voltage limit”.

6 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“12” (default value = 7.6V) then validate.

OBDeleven:

Method 2 (Temperature method):

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Minimaltemperatur”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“50” (default value = -50.0) and confirm.

Line 2:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Maximaltemperatur”.

6 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.

OBDeleven:

L’article Amarok (2H) – Start/Stop deactivation est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop completely.


Only compatible with Gateway 7N0! Temperature deactivation method.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on “Long Adaptation – 0A”.

5 – Select Channel“13

6 – In new value, select“D02000” (default value = 002000) then validate.

L’article Eos (1F) Facelift – Start/Stop deactivation est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop completely.


Only compatible with Gateway 7N0! Temperature deactivation method.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on “Long Adaptation – 0A”.

5 – Select Channel“13

6 – In new value, select“D02000” (default value = 002000) then validate.

L’article Caddy (2K) Facelift – Start/Stop deactivation est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop operation.

Information: Start/Stop is inactive as long as the air-conditioning control is “on”. As soon as this is switched off, Start/Stop is active again.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “08 – Air conditioning”.

4 – Click on “Adaptation – 10”.

5 – Select “channel IDE03253 – A/C comfort parameter for on-off function”.

base value: 5
replace with new value: 0

L’article Touareg 3 (CR) – Disabling Start & Stop est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop operation.

Information: Start/Stop is inactive as long as the air-conditioning control is “on”. As soon as it is switched off, Start/Stop becomes active again.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “08 – Air conditioning”.

4 – Click on “Adaptation – 10”.

5 – Select “channel IDE03253 – A/C comfort parameter for on-off function”.

base value: 5
replace with new value: 0

L’article Q8 (4M) – Disable Start & Stop est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop operation.

Information: Start/Stop is inactive as long as the air-conditioning control is “on”. As soon as it is switched off, Start/Stop becomes active again.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “08 – Air conditioning”.

4 – Click on “Adaptation – 10”.

5 – Select “channel IDE03253 – A/C comfort parameter for on-off function”.

base value: 5
replace with new value: 0

L’article A8 (D5) – Disable Start & Stop est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop operation.

Information: Start/Stop is inactive as long as the air-conditioning control is “on”. As soon as it is switched off, Start/Stop becomes active again.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “08 – Air conditioning”.

4 – Click on “Adaptation – 10”.

5 – Select “channel IDE03253 – A/C comfort parameter for on-off function”.

base value: 5
replace with new value: 0

L’article A7 (C8) – Disable Start & Stop est apparu en premier sur VAG Coding.

Purpose: to disable Start and Stop completely.

Watch out! There are 1 or 2 lines of coding to do here, depending on the method. (After 2019 deactivation no longer works according to gateway reference “AA”)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or OBDeleven.

2 – Switch on the ignition and run the VCDS program.

Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket:

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Limite de tension de départ marche/arrêt” / “Start/Stop voltage limit”.

6 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“12” (default value = 7.6V) then validate.

OBDeleven:

YouTube video:

Method 2 (Temperature method):

VCDS :

Line 1:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Minimaltemperatur”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“50” (default value = -50.0) and confirm.

Line 2:

3 – Click on“Select”, then click on“19 – CAN Gateway”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Start/Stopp Auntemperaturvorgabe-Maximaltemperatur”.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select“50” (default value = -50.0) and confirm.

OBDeleven:

L’article Q3 (F3) – Start/Stop deactivation est apparu en premier sur VAG Coding.