Purpose: displays speed limit signs in the Virtual Cockpit (Sign Assist).


The vehicle must be equipped with Lane Assist.


Warning! There are 8 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21_msg-bus”.

7 – On this same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“58”
Then, in the Bit 6-7 drop-down menu, select“40 VZE_traffic_sign_recognition,installed”.

Line 6 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 7 (optional) :

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display valid additional characters”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

Select byte“14”
Then check bit“6”:“traffic_sign_detection”.

L’article Touareg 3 (CR) – Virtual Cockpit panel display est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs in the Virtual Cockpit (Sign Assist).


The vehicle must be equipped with Lane Assist.


Warning! There are 8 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21_msg-bus”.

7 – On this same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“58”
Then, in the Bit 6-7 drop-down menu, select“40 VZE_traffic_sign_recognition,installed”.

Line 6 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 7 (optional) :

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display valid additional characters”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

Select byte“14”
Then check bit“6”:“traffic_sign_detection”.

L’article A8 (D5) – Panel display in Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs in the Virtual Cockpit (Sign Assist).


The vehicle must be equipped with Lane Assist.


Warning! There are 8 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21_msg-bus”.

7 – On this same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“58”
Then, in the Bit 6-7 drop-down menu, select“40 VZE_traffic_sign_recognition,installed”.

Line 6 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 7 (optional) :

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display valid additional characters”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

Select byte“14”
Then check bit“6”:“traffic_sign_detection”.

L’article A7 (C8) – Panel display on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs in the Virtual Cockpit (Sign Assist).


The vehicle must be equipped with Lane Assist.


Warning! There are 8 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule function list BAP-traffic_sign_recognition_0x21_msg-bus”.

7 – On this same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicule menu operation-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“58”
Then, in the Bit 6-7 drop-down menu, select“40 VZE_traffic_sign_recognition,installed”.

Line 6 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 7 (optional) :

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display valid additional characters”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

Select byte“14”
Then check bit“6”:“traffic_sign_detection”.

L’article A6 (C8) – Panel display on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs in the Virtual Cockpit (Sign Assist).


Vehicle must be equipped with 3Q0 camera


Warning! There are 9 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.5F – Information Electr.”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“24”
Select Bit 6

Line 6:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“16”
Then, in the Bit 4 drop-down menu, select“Traffic sign recognition (VZE) active [PR-QR9]”.

Line 7 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Road Sign Detection Fusion Mode” /“Détection des panneaux de signalisation mode fusion”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Traffic sign detection” to use camera recognition only, or“Traffic sign fusion” for camera + gps speed, then confirm.

Line 9:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

L’article Tarraco (KN) – Panel display on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs on the ODB/Virtual Cockpit (Sign Assist)


Vehicle must be equipped with 3Q0 camera


Warning! There are 9 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.5F – Information Electr.”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“24”
Select Bit 6

Line 6:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“16”
Then, in the Bit 4 drop-down menu, select“Traffic sign recognition (VZE) active [PR-QR9]”.

Line 7 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Road Sign Detection Fusion Mode” /“Détection des panneaux de signalisation mode fusion”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Traffic sign detection” to use camera recognition only, or“Traffic sign fusion” for camera + gps speed, then confirm.

Line 9:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

L’article Taigo (CS) – Panel display on ODB est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs on the ODB/Virtual Cockpit (Sign Assist)


Vehicle must be equipped with 3Q0 camera


Warning! There are 9 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.5F – Information Electr.”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“24”
Select Bit 6

Line 6:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“16”
Then, in the Bit 4 drop-down menu, select“Traffic sign recognition (VZE) active [PR-QR9]”.

Line 7 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Road Sign Detection Fusion Mode” /“Détection des panneaux de signalisation mode fusion”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Traffic sign detection” to use camera recognition only, or“Traffic sign fusion” for camera + gps speed, then confirm.

Line 9:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

L’article Kamiq (NW) – Sign display on ODB est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs on the ODB/Virtual Cockpit (Sign Assist)


Vehicle must be equipped with 3Q0 camera


Warning! There are 9 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.5F – Information Electr.”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“24”
Select Bit 6

Line 6:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“16”
Then, in the Bit 4 drop-down menu, select“Traffic sign recognition (VZE) active [PR-QR9]”.

Line 7 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Road Sign Detection Fusion Mode” /“Détection des panneaux de signalisation mode fusion”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Traffic sign detection” to use camera recognition only, or“Traffic sign fusion” for camera + gps speed, then confirm.

Line 9:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

L’article Superb (3V) Facelift – Panel display on ODB / Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs in Virtual Cockpit (Sign Assist)


Vehicle must be equipped with 3Q0 camera (until 2020)


Warning! There are 9 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.5F – Information Electr.”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“24”
Select Bit 6

Line 6:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“16”
Then, in the Bit 4 drop-down menu, select“Traffic sign recognition (VZE) active [PR-QR9]”.

Line 7 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Road Sign Detection Fusion Mode” /“Détection des panneaux de signalisation mode fusion”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Traffic sign detection” to use camera recognition only, or“Traffic sign fusion” for camera + gps speed, then confirm.

Line 9:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

L’article Q3 (F3) – Panel display on Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: displays speed limit signs on the ODB/Virtual Cockpit (Sign Assist)


Vehicle must be equipped with 3Q0 camera


Warning! There are 9 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-traffic_sign_recognition_0x21_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_road_sign_identification_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 5:

3 – Click on“Select” then click on “.5F – Information Electr.”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“24”
Select Bit 6

Line 6:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“16”
Then, in the Bit 4 drop-down menu, select“Traffic sign recognition (VZE) active [PR-QR9]”.

Line 7 (Optional):

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Display end of speed limit symbol”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“activated” and confirm.

Line 8:

3 – Click on“Select” then click on “.A5 – Frt Sens. Drv. Assist“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Road Sign Detection Fusion Mode” /“Détection des panneaux de signalisation mode fusion”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose“Traffic sign detection” to use camera recognition only, or“Traffic sign fusion” for camera + gps speed, then confirm.

Line 9:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“5”
Then check Bit“2”:“Traffic Sign Recognition installed”.

L’article Q2 (GA) – Panel display on ODB / Virtual Cockpit est apparu en premier sur VAG Coding.