Purpose: to add Offroad mode to the Easy Connect MIB V2 screen with navigation.


Watch out! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Additional line if OFF Road not activated :

Car_Function_Adaptations_Gen2

menu_display_compass: change the value to “activated” [Standard: “Not activated”]
menu_display_compass_over_therhold_high: change the value to “activated” [Standard: “Not activated”]
menu_display_angle_of_slope: change the value to “activated” [Standard: “Not activated”]
menu_display_angle_of_slope_over_threshold_high: change the value to “activated” [Standard: “Not activated”]

Car_Function_List_Bap_Gen2

compass_0x15: change the value to “activated” [Standard: “Not activated”]
compass_0x15_msg_bus: change the value to “Comfort data bus”
angle_of_slope_0x24: change the value to “activated” [Standard: “Not activated”]
angle_of_slope_0x24_msg_bus: change the value on “Comfort data bus”

L’article Toledo (NH) – Activate Off-Road mode est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to the Easy Connect MIB V2 screen with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Additional line if OFF Road not activated :

Car_Function_Adaptations_Gen2

menu_display_compass: change the value to “activated” [Standard: “Not activated”]
menu_display_compass_over_therhold_high: change the value to “activated” [Standard: “Not activated”]
menu_display_angle_of_slope: change the value to “activated” [Standard: “Not activated”]
menu_display_angle_of_slope_over_threshold_high: change the value to “activated” [Standard: “Not activated”]

Car_Function_List_Bap_Gen2

compass_0x15: change the value to “activated” [Standard: “Not activated”]
compass_0x15_msg_bus: change the value to “Comfort data bus”
angle_of_slope_0x24: change the value to “activated” [Standard: “Not activated”]
angle_of_slope_0x24_msg_bus: change the value on “Comfort data bus”

L’article Ibiza (6P) – Activate Off-Road mode est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Caddy 4 (2K) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Scirocco (13) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Tiguan (5N2) Facelift – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Sharan (7N) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Beetle (5C) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Amarok (2H) Facelift – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Transporter (T6) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to the Amundsen MIB screen with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Fabia (NJ) – Activate Off-Road mode est apparu en premier sur VAG Coding.