Purpose: to add the stopwatch to the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on ” 10 – Adaptation

5 – Select Channel 36 “Special Functions”
Add +1 to the existing value as specified in the bubble (x?x).

Example: original value 001: change to 011

L’article R8 (42) – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the ODB/Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“1”
Then check Bit“3”:“Lap Timer active”.

L’article A8 (D5) – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the ODB (on-board computer).

ATTENTION: Only for TTS and TT Facelift compatible according to meter.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on ” 10 – Adaptation

5 – Select Channel 36 “Special Functions”
Add +1 to the existing value as specified in the bubble (x?x).

Example: origin value 01 or 1: change to 11 / origin value 00: change to 10 / origin value 000: change to 010

L’article TT (8J) Facelift – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the ODB (on-board computer).

ATTENTION: Only for S3 and A3 Facelift compatible according to meter.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on ” 10 – Adaptation

5 – Select Channel 36 “Special Functions”
Add +1 to the existing value as specified in the bubble (x?x).

Example: origin value 01 or 1: change to 11 / origin value 00: change to 10 / origin value 000: change to 010

L’article A3 (8P) Facelift – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the ODB/Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“1”
Then check Bit“3”:“Lap Timer active”.

Alternative method if the 1st doesn’t work!! :


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Lap counter”.

6 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Display” and confirm.

L’article Karoq (NU) – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the ODB/Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“1”
Then check Bit“3”:“Lap Timer active”.

L’article Fabia 4 (PJ) – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the ODB/Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“1”
Then check Bit“3”:“Lap Timer active”.

Alternative method if the 1st doesn’t work!! :


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Lap counter”.

6 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Display” and confirm.

L’article Scala (NW) – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“1”
Then check Bit“3”:“Lap Timer active”.

L’article A1 (GB) – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the ODB/Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“1”
Then check Bit“3”:“Lap Timer active”.

L’article Arona (KJ) – Lap Timer est apparu en premier sur VAG Coding.

Purpose: to add the stopwatch to the Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“1”
Then check Bit“3”:“Lap Timer active”.

L’article Q3 (F3) – Lap Timer est apparu en premier sur VAG Coding.