Purpose: deactivates interior lighting when only the trunk is opened.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347 “.

5 – Click on“Adaptation – 10 “.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior lighting Innenlicht-bei offenem Heckdeckel einschalten“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“inactive” and confirm.

L’article Q2 (GA) – Interior lighting off when trunk is opened est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights switch on and off immediately with the headlights. Activating this function will cause a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Suchbeleuchtung_allgemein – KL58 Einschalten mit Rampe“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article Born (K11) – Activates progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights switch on and off immediately with the headlights. Activating this function will cause a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Suchbeleuchtung_allgemein – KL58 Einschalten mit Rampe“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article Enyaq (NY) – Activation of progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights are switched on and off immediately with the headlights. Activating this function will result in a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Suchbeleuchtung_allgemein – KL58 Einschalten mit Rampe“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article ID.4 (E2) – Activation of progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights are switched on and off immediately with the headlights. Activating this function will result in a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Suchbeleuchtung_allgemein – KL58 Einschalten mit Rampe“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article ID.3 (E1) – Activation of progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: activates ambient lighting and menu on MMI (after wiring and lighting of floor stand and/or door for retrofitting).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Coding for the MMI ambient lighting menu :

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle function list BAP-interieur_light_0x08“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle menu operation-menu_display_ambient_illumination“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle menu operation-menu_display_ambient_illumination_over_threshold_high“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart MMI

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior light, light configuration- Ambiente_Applikationsleisten_in_Tuertafel“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Installed” and confirm.

Line 5:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interior light, light configuration- Ambiente_Lautsprecher“

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Installed” and confirm.

Line 6:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interior light, light configuration- Fussraumbeleuchtung“

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Installed” and confirm.

Coding for foot/floor light :

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Int. light, 2nd generation : Defaultwert Ambienteprofil Fussraum“

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select”100″ and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte30FR LC72 – Lichtfunktion A 30“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Footwell Light” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte30FR LC72 – Dimmwert AB 30“.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select”100″ and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 5

Set bit 7 “Footwell Lights Installed

Coding for Door Light :

Line 1:

3 – Click on“Select” then click on“42-Driver door“.

4 – Click on“Coding – 07“.

5 – Select byte 01 and check bit 1 “Ambient Lighting installed”.

Line 2:

3 – Click on“Select”, then click on“52 – Passenger door“.

4 – Click on“Coding – 07“.

5 – Select byte 01 and check bit 1 “Ambient Lighting installed”.

L’article A3 (8V) – Activate ambient lighting est apparu en premier sur VAG Coding.

Purpose: to increase the intensity of door lighting.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte16BLK SLB35BLK SL KC9-Dimmwert AB 16”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte17TFL R BLK SRB3TFL R SR KC3-Dimmwert AB 17”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

L’article Tiguan 2 (AD1) – Increase door lighting intensity est apparu en premier sur VAG Coding.

Purpose: to increase the intensity of door lighting.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte16BLK SLB35BLK SL KC9-Dimmwert AB 16”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte17TFL R BLK SRB3TFL R SR KC3-Dimmwert AB 17”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

L’article Passat (B8) – Increase door lighting intensity est apparu en premier sur VAG Coding.

Purpose: to modify the intensity of ambient lighting at foot level.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte30FR LC72-Dimmwert AB 30”.

7 – On this same page is a second drop-down menu, but at the bottom
of the page.
On this, choose“127” then validate. (Default is“89”).

L’article Passat (B8) – Increase floor lighting intensity est apparu en premier sur VAG Coding.

Purpose: to increase the intensity of door lighting.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte16BLK SLB35BLK SL KC9-Dimmwert AB 16”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte17TFL R BLK SRB3TFL R SR KC3-Dimmwert AB 17”.

7 – On this same page is a second drop-down menu, but towards the bottom
of the page.
On this, choose“127” then validate. (Default is “100”).

L’article Golf 7 (5G) – Increase door lighting intensity est apparu en premier sur VAG Coding.