Purpose: to deactivate the ACC lane assist system, e.g. when on the freeway and there is a traffic jam in the left lane, the vehicle starts to slow down.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg “.

4 – Click on“Coding – 07” then“Long Coding Helper“.

5 – Uncheck the Bit: “overtaking_right_prevention“

OBDeleven: Select “overtaking_right_prevention”
Change from “activated” to “Deactivated”.

L’article Born (K11) – Deactivate right-hand overtaking prevention est apparu en premier sur VAG Coding.

Purpose: to deactivate the ACC lane assist system, e.g. when on the freeway and there is a traffic jam in the left lane, the vehicle starts to slow down.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg “.

4 – Click on“Coding – 07” then“Long Coding Helper“.

5 – Uncheck the Bit: “overtaking_right_prevention“

OBDeleven: Select “overtaking_right_prevention”
Change from “activated” to “Deactivated”.

L’article Enyaq (NY) – Disable right overtaking prevention est apparu en premier sur VAG Coding.

Purpose: to deactivate the ACC lane assist system, e.g. when on the freeway and there is a traffic jam in the left lane, the vehicle starts to slow down.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg “.

4 – Click on“Coding – 07” then“Long Coding Helper“.

5 – Uncheck the Bit: “overtaking_right_prevention“

OBDeleven: Select “overtaking_right_prevention”
Change from “activated” to “Deactivated”.

L’article ID.4 (E2) – Deactivate right-hand overtaking prevention est apparu en premier sur VAG Coding.

Purpose: to deactivate the ACC lane assist system, e.g. when on the freeway and there is a traffic jam in the left lane, the vehicle starts to slow down.

SFD: no

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg “.

4 – Click on“Coding – 07” then“Long Coding Helper“.

5 – Uncheck the Bit: “overtaking_right_prevention“

OBDeleven: Select “overtaking_right_prevention”
Change from “activated” to “Deactivated”.

L’article ID.3 (E1) – Deactivate right-hand overtaking prevention est apparu en premier sur VAG Coding.

Purpose: to adjust the ACC distance setting from the factory setting so that it can be set in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control system adjust your speed in 10 km/h increments. You can change the coding in 1 km/h increments by briefly pressing the button. And use the old speed increments of 5 mph or 10 km/h by pressing and holding the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Select bit 6 “Operation Mode 2”.

Some speed controller modules may use a different coding or even have this parameter as an adaptation instead of the coding. Make sure that the option you are about to modify is correctly labeled.

Module 13 → Adaptation → Mode de fonctionnement / Operation Mode → Mode de fonctionnement 2 / Operation Mode 2

L’article Touran (2T) – Set ACC control in 1 km/h increments est apparu en premier sur VAG Coding.

Purpose: to adjust the ACC distance setting from the factory setting so that it can be set in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control system adjust your speed in 10 km/h increments. You can change the coding in 1 km/h increments by briefly pressing the button. And use the old 10 km/h speed increments by pressing and holding the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Select bit 6 “Operation Mode 2”.

Some speed controller modules may use a different coding or even have this parameter as an adaptation instead of the coding. Make sure that the option you are about to modify is correctly labeled.

Module 13 → Adaptation → Mode de fonctionnement / Operation Mode → Mode de fonctionnement 2 / Operation Mode 2

L’article Leon (5F) Facelift – Set ACC control in 1 km/h increments est apparu en premier sur VAG Coding.

Purpose: to adjust the ACC distance setting from the factory setting so that it can be set in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control system adjust your speed in 10 km/h increments. You can change the coding in 1 km/h increments by briefly pressing the button. And use the old 10 km/h speed increments by pressing and holding the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Select bit 6 “Operation Mode 2”.

Some speed controller modules may use a different coding or even have this parameter as an adaptation instead of the coding. Make sure that the option you are about to modify is correctly labeled.

Module 13 → Adaptation → Mode de fonctionnement / Operation Mode → Mode de fonctionnement 2 / Operation Mode 2

L’article Superb (3V) Facelift – Adjust ACC control in 1 km/h increments est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Karoq (NU) – Front Assist settings est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Kodiaq (NS) – Front Assist settings est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Tarraco (KN) – Front Assist settings est apparu en premier sur VAG Coding.