Purpose : to activate GRA cruise control (retrofit).

Modification only possible after retrofitting cruise control switch and check that your multifunction steering wheel is compatible (midline or highline).

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 01 – Motor “.

4 – Click on ” Coding II (11) or Login 11 “.

5 – Then enter code 11463, then OK (Do It!)

The code 11463 is used to activate the controller, to deactivate it if necessary the code is 16167.

Line 2:

3 – Click on ” Select “, then click on ” 16 – Multifunction handwheel “.

4– Click on ” Coding – 07 “.

5 – Options: We note in the penultimate section (0xxxx?x):

0 = No regulator installed (CCS not installed)
1 = Regulator installed with 6 positions on a separate switch (CCS with 6 positions …. etc)
3 = Regulator installed with 4 positions on the blinker switch (CCS with 4 positions via Blinker Stalk)

So replace the “?” with the 3 for commodo regulator.

Line 3:

3 – Click on ” Select”, then click on ” Select “. 01 – Engine ” .

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte“5“
Check bit“5” Cruise Control System (CCS) installed

Or byte 6 bit 0

L’article Touran (1T3) – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.

Purpose: to display the amount of fuel topped up on the ODB (on-board computer).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on “Adaptation – 10” .

5 – Select “Volume to be Replenished” from the value list.

Select ” Yes ” in the second value list.

L’article Touran (1T3) – Top-up quantity displayed on ODB est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the on-board computer.

Modification only possible on Mid/High range models.
Note: modifications affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel 03 “Consumption Correction”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96

L’article Touran (1T3) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: to change the vehicle image of the OPS (parking aid) on the RCD 510/330/360/440 and RNS 315/510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding 07” then “Long Coding Helper”.

5 – Choose Byte 6 or 9

Selectthe vehicle from the drop-down menu:

00 = via CAN
01 = Polo 6R
02 = New Beetle
03 = New Beetle Cabrio
04 = Scirocco
05 = Golf 5
06 = Jetta
07 = Golf 6 Variant
08 = Golf 6 Cabrio
09 = Touran
0A = Golf Plus
0C = Tiguan
0D = Sharan
0E = EOS
0F = Passat 3C
10 = Passat Limousine
11 = Passat Variant
13 = Caddy
14 = T5
2C = Skoda Octavia
2D = Skoda Octavia Kombi
2E = Skoda Superb Kombi

Exit the module and save your changes. The RCD or RNS must now be restarted for the changes to take effect. Press both arrows and the star for 6s.

L’article Touran (1T3) – Changing the image of the RCD/RNS OPS est apparu en premier sur VAG Coding.

Purpose : to adjust the hardness of the power steering for a softer or harder steering wheel.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.

4 – Click on“Adaptation – 10”.

5 – Select Channel 1 , set a value between 1 and 15 depending on your hardness preference.

Or Line 2: (If channel 1 is unavailable):

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.

4 – Click on“Coding – 07”.

5 – Select :

• xxx1x for smooth steering
• xxx2x for sports management
• xxx3x for hard steering
• xxx4x for harder steering
• xxx5x for very hard steering

L’article Touran (1T3) – Modify power steering hardness est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after installation on the RCD 510/330/360/440 and RNS 315/510 (retrofit).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 3
Then check bit 6 “Rear View Camera (RVC) installed/active”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Assistance Stationn”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 0
Then check bit 5 “Rear View Camera installed”.

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Touran (1T3) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Touran (1T3) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Touran (1T3) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to activate voice control on the RNS 510 (SDS).

ATTENTION: RNS 510 firmware must be version v2660.

Activating voice control brings up the “Voice control” menu in the RNS 510’s SETUP menu.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3, check the box for“Bit 1: Microphone Diagnostics active”.

Byte 7, uncheck the box for“Bit 1: Voice Control inactive”.

To install the microphone, connect the microphone lead to the rear of the RNS 510. Connect to pins (Mic-)C1 and (Mic+)C7.

L’article Touran (1T3) – Activate RNS 510 voice control est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Volkswagen Touran 2 (1T3)
–> Buy your OBDeleven device with VAG Custom

VW Touran 2 (1T3) (2010-2015)

• Activate Bluetooth RNS315
• Air recirculation memory
• Automatic locking/unlocking
• Automatic reverse wiping
• Central locking with IGN
• Comfort flashing light
• Time to return home
• Bending lights
• Bending lights with reverse
• Driver’s seat heating memory
• DRL Gradation
• DRL in MFD+
• DRL indicator in dashboard
• DRL OFF with handbrake ON
• DRL parameters
• DRL with ADL
• Emergency brake flashing with trailer
• Emergency brake lights
• Fog lamps with high beam
• Floor lighting
• Headlamp washer
• Heating test
• Heating release
• High beam assistance by region (LHD/RHD)
• High beam assistance city recognition
• High beam speed threshold
• Freeway lights
• Inspection service reset
• Departure time
• LED license plate lamps
• Low beam speed threshold
• MirrorLink on the move 1
• MirrorLink on the move 2
• Oil service reset
• PTT button options
• Rain lights
• Drop-shaped rear wiper
• Rear window wiper
• Remote window function
• RNS 310/315 CD lock
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 reversing camera
• SDS RNS 310/315
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• Speed limit RNS 510
• RNS 510 theme
• Synchronized mirror adjustment
• Teardrop wipe
• Video in motion V2
• Window and mirror heater activation time
• Windshield wiper control
• Automatic return lights
• Automatic closing in case of rain
• Type of CH light activation
• CH/LH lights
• CH/LH lights via dipped beam/fog lights
• Motor fan test
• Fuel system priming
• Heater on/off
• Needle sweep
• Engine oil type
• Inspection service distance
• Inspection service interval
• Multimedia restart
• Multimedia security disclaimer
• Oil change service distance
• Oil change Service interval
• Warning of impending maintenance

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article List OBDeleven One-Click Apps TOURAN (1T3) est apparu en premier sur VAG Coding.