Purpose: to adjust the hardness of the power steering for a softer steering wheel (Comfort) or a harder sporty one (Dynamic).
Warning: if you have the driving mode selection, do not modify!

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“44 – Steering Assistance”.

4 – Click on“Security Access – 16” then enter the code“19249”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Courbes caractéristiques d’assistance de direction” /“Characteristic curve of steering assistance”

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose the value:“Confort” or “Dynamic” then validate.

selection_by_charisma: You have the driving modes, do not modify this value otherwise you will lose the hardness of the steering wheel according to your driving mode!

L’article Taigo (CS) – Modify power steering hardness est apparu en premier sur VAG Coding.

Purpose: activates the RES button to act as a gas pedal while using ACC. Holding down the RES button allows the vehicle to reach a previously set speed faster than usual. (Boost ACC – Adaptive Cruise Control)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or OBDeleven.

2 – Switch on the ignition and run the VCDS program. or OBDeleven.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Set bit 07 “Boost Function”.

OBDeleven: Select “Boost Function”
Change from “desactivated” to “Activated”.

L’article Taigo (CS) – Activate ACC gas pedal button est apparu en premier sur VAG Coding.

Purpose: to adjust the ACC distance setting from the factory setting so that it can be set in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control system adjust your speed in 10 km/h increments. You can change the coding in 1 km/h increments by briefly pressing the button. And use the old 10 km/h speed increments by pressing and holding the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Select bit 6 “Operation Mode 2”.

Some speed controller modules may use a different coding or even have this parameter as an adaptation instead of the coding. Make sure that the option you are about to modify is correctly labeled.

Module 13 → Adaptation → Mode de fonctionnement / Operation Mode → Mode de fonctionnement 2 / Operation Mode 2

L’article Taigo (CS) – Set ACC control in 1 km/h increments est apparu en premier sur VAG Coding.

Purpose: to deactivate the beep when reverse gear is engaged or when parking assistance is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Tonalité d’activation de l’aide au stationnement ” / “Park assist activation tone ” / “Aktivierungston für Einparkhilfe ” from value list

7 – Select “Off” in the second value list

L’article Taigo (CS) – Deactivation of parking aid activation beep est apparu en premier sur VAG Coding.

Purpose: activates window operation (close/open) with ignition off and door open.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access control 2-Freigabenachlauf FH bei Kl 15 aus”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, select“active”, then confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access control 2-Freigabenachlauf FH bei Tueroeffnen abbrechen”.

7 – On the same page, there’s a second drop-down menu at the bottom of the page.
On this menu, select“not active”, then confirm.

L’article Taigo (CS) – Activate window operation with ignition off est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Volkswagen Taigo (CS)
–> Buy your OBDeleven device with VAG Custom

VW Taigo CS (2021+ ) / (Nivus)

• Air conditioning damper calibration
• Adaptive lane guidance
• Automatic return lights
• Automatic PDC activation
• Brake check when using ACC
• Brake pad warning
• Central locking with IGN
• Type of CH light activation
• Comfort turn signals
• Comfort windows
• Activating cruise control
• Daytime running lights on/off
• DRL activated with AUTO
• Main unit daytime running light settings
• DRL with fog lights
• DRL disabled with handbrake
• Efficiency program
• Emergency brake lights
• Fog lights with door open
• Fog lights with high beam
• Fog lights with headlamp flashing
• Footwell with blinker
• Front fog lights in reverse
• Fuel system priming
• Gauge test – Needle sweep
• Headlamp washer
• High beam assistance
• High beam assistance memory
• High-intensity brake light
• Hill-start assist settings
• Inspection service reset
• Instrument group logo
• Interior lighting discoloration
• Lane assist parameters memory
• Tower Timer
• Acoustic confirmation of locking/unlocking
• Mirror indicators with CH/LH
• Oil service reset
• One-touch power window settings
• Fuel quantity in instrument panel
• Scandinavian daytime running lights
• Seat belt warning
• The horn is always ready for use
• Speed limiter
• Rear lights as brake lights
• Rear lights with door open
• Third brake light when trunk is open
• Third brake light with CH/LH lights
• Turn signals with door open
• Turn signals with brake lights
• Washer fluid indicator
• Closing windows after locking
• Climate control settings for hot climates
• ACC distance settings menu
• ACC speed gas pedal
• Adjust ACC in 1 km/h steps
• Alternate parking position for windshield wipers
• Automatically folding mirrors
• Automatic headlight settings
• Automatic exit lock
• Automatic locking/unlocking
• Automatic unlocking after P
• Automatic door handle release
• Automatic windshield defrost
• Battery capacity
• Battery type
• Brake light test
• Brake lights when trunk is open
• Ambient center line Turn signal with flasher
• CH/LH light variant
• Climatronic menu in multimedia
• Comfort flashing light
• Comfort glass menu
• Time to return home
• Consumption display correction
• Bend light attenuation rate
• Door lock test all
• DRL on with parking lights
• Motor fan test
• Engine oil type
• Fog lights with indicators
• Fog lights off with high beam
• Left front door lock test
• Urban Joke” front Pace-Car turn signals
• Front parking assistance volume
• Front parking assistance tone
• Front right door lock test
• Emergency light switch
• Beacon notification
• Headlamp washer test
• Memory for heated seats
• Inspection service distance
• Inspection service interval
• Track assistance information message
• Track assistance warning level
• Home departure time
• LED foot lighting
• Bright LED footlights
• License plate illumination with DRL
• License plate illumination with trunk open
• Flashing lock button with safety light
• Locking button color
• Sound lock/unlock Settings
• Low ambient temperature warning
• Multimedia mirror tilt adjustment
• Mirror turn signal with high beam
• Multimedia restart
• Multimedia start logo
• Oil change service distance
• Oil change service interval
• Oil temperature display
• Open door alarm
• Optical parking system
• Park assist activation tone
• Parking assist deactivation speed
• Parking lights on both sides
• Phone in dashboard
• Power windows with IGN OFF
• Start button pulse
• Rear fog light warning
• Left rear door lock test
• Rear parking assistance volume
• Rear parking assistance tone
• Right rear door lock test
• Back-up light test
• Type of seat belt warning
• Warning of impending maintenance
• Speed-dependent wipers
• Speed warning
• Speedometer scale range
• Start button dimming
• Static bend lights
• Static bend light parameters
• Rear lights when trunk is open
• Accelerator pedal response
• TPMS reset
• Turn signal test
• Turn signals when trunk is open
• Turn signals with position lights
• Motion video disabled
• Motion video enabled
• Virtual cockpit theme

---

Coding list VCDS / OBDeleven VW Taigo CS

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps TAIGO (CS) list est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights are switched on and off immediately with the headlights. Activating this function will cause a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior lighting-KL58 Einschalten mit Rampe”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article Taigo (CS) – Activation of progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: to set Hill Start Assist operation. (hill-start assist)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“03 – ABSBrakes ”.

4 – Click on“Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Hill Start assistant” / “Assistant démarrage en côte”.

6 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On this, choose the value according to your preference:

• “normal” (default value)
• “Early” (faster triggering)
• “Late” triggering

then validate.

L’article Taigo (CS) – Hill Start Assist est apparu en premier sur VAG Coding.

Purpose: automatically unlocks all doors when the DSG automatic gearbox is shifted to “P”.

Procedure:
1– Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

3 – Click on “Select” then click on “09 – Cent. Elect.”.

4 – Click on “Security Access – 16” then enter the code “31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Access control – Autounlock NAR”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, choose “active”, then confirm.

L’article Taigo (CS) – Automatic door unlocking with DSG in “P” position est apparu en premier sur VAG Coding.

Purpose: automatically closes the windows when the car is locked. A new menu will be activated in door settings to deactivate the option if required.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ZV Komfort Fensterheber – Komfortschliessen Brasilien”.ZV Komfort Fensterheber – Komfortschliessen Brasilien“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Komfort Fensterheber – BAP Komfortschliessen Brasilien”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Taigo (CS) – Automatically closes windows when locked est apparu en premier sur VAG Coding.