Purpose: to correct the fuel consumption display on the Trip Computer/Virtual Cockpit.

Note: these changes affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel: “Display correction of consumptions and operating range”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96.

Example 3: the consumption announced by the ODB is 5.9l/100km, after checking it is actually 6.3l/100km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%, and the consumption announced by the ODB will be a pessimistic 0.1l/100km.

Consumption is immediately modified on the Discover MIB :

L’article T-Cross (C1) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: to keep the 3rd brake light on if the trunk is not fully closed. For security lighting at night or to make sure your safe is securely closed.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte22BR MC9-Lichtfunktion C 22”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, select the value“Heckdeckel Offen” and confirm. (Origin: nicht aktiv)


Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte22BR MC9-Dimmwert CD 22”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“100” depending on the power of the brake light, then confirm. (Origin: 0)

L’article T-Cross (C1) – Third brake light on when trunk is open est apparu en premier sur VAG Coding.

Purpose: to adjust the hardness of the power steering for a softer steering wheel (Comfort) or a harder sporty one (Dynamic).
Warning: if you have the driving mode selection, do not modify!

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“44 – Steering Assistance”.

4 – Click on“Security Access – 16” then enter the code“19249”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Courbes caractéristiques d’assistance de direction” /“Characteristic curve of steering assistance”

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose the value:“Confort” or “Dynamic” then validate.

selection_by_charisma: You have the driving modes, do not modify this value otherwise you will lose the hardness of the steering wheel according to your driving mode!

L’article T-Cross (C1) – Modifying power steering hardness est apparu en premier sur VAG Coding.

Purpose: to adjust the intensity of the hands-free system’s microphone.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Microphone sensitivity” or “Mikrofonempfindlichtkeit”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose a value expressed in“dB” (default value“0 dB”) then validate.

L’article T-Cross (C1) – Microphone sensitivity adjustment est apparu en premier sur VAG Coding.

Purpose: to modify the vehicle on the Active Info Display / Virtual Cockpit.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“02“
Then select Bit“3-6“: ” “.Model: Variant X“

Choose the Variant corresponding to the desired vehicle.

Example of a Variant :

Variant 2: Golf 7 GTI 5-door
Variant 3: Golf 7 GTI 3-door
Variant 6: Golf 7R 5-door
Variant 7: Golf 7R 3-door

L’article T-Cross (C1) – Modifying the vehicle in the Virtual Cockpit est apparu en premier sur VAG Coding.

Purpose: Allows you to disable / remove MirrorLink from App-Connect on MIB Discover. The Mirrorlink service is no longer available since June 1, 2020 on Android natively. For direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article T-Cross (C1) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: to display a compass on the ODB (on-board computer), if you have GPS navigation (NAV), and to change its position on the speedo.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“10”
Then check Bit“6”.

Line 2 (if line 1 unavailable) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “Navigation /Compass” channel.

6 – In the “Value:” option, select“Enabled”.

Line 3 (to change the compass position on the ODB) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. From this drop-down menu, select the “Compass indicator” channel.

6 – In the “Value:” option, select the desired value for the compass position on the ODB (default: lower position).

L’article T-Cross (C1) – Compass display on ODB est apparu en premier sur VAG Coding.

Purpose: to display oil temperature on the ODB/Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“10”
Then check Bit“1”:“Display Oil Temperature”.

L’article T-Cross (C1) – Oil temperature on ODB est apparu en premier sur VAG Coding.

Purpose: activates the RES button to act as a gas pedal while using ACC. Holding down the RES button allows the vehicle to reach a previously set speed faster than usual. (Boost ACC – Adaptive Cruise Control)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or OBDeleven.

2 – Switch on the ignition and run the VCDS program. or OBDeleven.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Set bit 07 “Boost Function”.

OBDeleven: Select “Boost Function”
Change from “desactivated” to “Activated”.

L’article T-Cross (C1) – Activate ACC gas pedal button est apparu en premier sur VAG Coding.

Purpose: to adjust the ACC distance setting from the factory setting so that it can be set in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control system adjust your speed in 10 km/h increments. You can change the coding in 1 km/h increments by briefly pressing the button. And use the old 10 km/h speed increments by pressing and holding the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Select bit 6 “Operation Mode 2”.

Some speed controller modules may use a different coding or even have this parameter as an adaptation instead of the coding. Make sure that the option you are about to modify is correctly labeled.

Module 13 → Adaptation → Mode de fonctionnement / Operation Mode → Mode de fonctionnement 2 / Operation Mode 2

L’article T-Cross (C1) – Set ACC control in 1 km/h increments est apparu en premier sur VAG Coding.