Purpose: to change the vehicle image of the OPS (parking aid) on the RCD 510/330/360/440 and RNS 315/510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding 07” then “Long Coding Helper”.

5 – Choose Byte 6 or 9

Selectthe vehicle from the drop-down menu:

00 = via CAN
01 = Polo 6R
02 = New Beetle
03 = New Beetle Cabrio
04 = Scirocco
05 = Golf 5
06 = Jetta
07 = Golf 6 Variant
08 = Golf 6 Cabrio
09 = Touran
0A = Golf Plus
0C = Tiguan
0D = Sharan
0E = EOS
0F = Passat 3C
10 = Passat Limousine
11 = Passat Variant
13 = Caddy
14 = T5
2C = Skoda Octavia
2D = Skoda Octavia Kombi
2E = Skoda Superb Kombi

Exit the module and save your changes. The RCD or RNS must now be restarted for the changes to take effect. Press both arrows and the star for 6s.

L’article Sharan (7N) – Changing the image of RCD/RNS OPS est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Sharan (7N) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: To deactivate / remove MirrorLink from App-Connect on the Discover PQ MIB. The Mirrorlink service is no longer available since June 1, 2020 on Android natively. For direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Sharan (7N) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after installation on the RCD 510/330/360/440 and RNS 315/510 (retrofit).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 3
Then check bit 6 “Rear View Camera (RVC) installed/active”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Assistance Stationn”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 0
Then check bit 5 “Rear View Camera installed”.

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Sharan (7N) – Activate reversing camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Sharan (7N) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Sharan (7N) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to activate voice control on the RNS 510 (SDS).

ATTENTION: RNS 510 firmware must be version v2660.

Activating voice control brings up the “Voice control” menu in the RNS 510’s SETUP menu.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3, check the box for“Bit 1: Microphone Diagnostics active”.

Byte 7, uncheck the box for“Bit 1: Voice Control inactive”.

To install the microphone, connect the microphone lead to the rear of the RNS 510. Connect to pins (Mic-)C1 and (Mic+)C7.

L’article Sharan (7N) – Activate RNS 510 voice control est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Volkswagen Sharan (7N)
–> Buy your OBDeleven device with VAG Custom

VW Sharan 7N (2010-2022)

• Activate Bluetooth RNS315
• Air recirculation memory
• Automatic locking/unlocking
• Automatic reverse wiping
• Brake pad wear indicator
• Brake pad replacement
• Central locking with IGN
• Folding comfort mirrors
• Comfort flashing light
• Time to return home
• Bending lights
• Bending lights with reverse
• Driver’s seat heating memory
• Driving school mode
• DRL in MFD+
• DRL indicator in dashboard
• DRL OFF with handbrake ON
• DRL settings
• DRL with ADL
• Easy entry
• Emergency brake flashing with trailer
• Emergency brake lights
• Fog lamps with high beam
• Floor lighting
• Gauge test – Needle sweep
• Headlamp washer
• Heating test
• Unlocking the heater
• High beam assistance by region (LHD/RHD)
• Recognition of high beam assistance in town
• High beam speed threshold
• Freeway lights
• Inspection service reset
• Departure time
• LED license plate lamps
• Low beam speed threshold
• MirrorLink on the move 1
• MirrorLink on the move 2
• Oil reset service
• PTT button options
• Rain lights
• Rear cover control
• Drop-shaped rear wiper
• Rear window wiper
• Remote window function
• CD lock RNS 310/315
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 reversing camera
• SDS RNS 310/315
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• Speed limit RNS 510
• RNS 510 theme
• Seat belt warning
• Drop-shaped wiping
• Washer fluid indicator
• Window and mirror heater activation time
• Windshield wiper control
• Automatic return lights
• Automatic closing in case of rain
• Brake assist parameters
• Type of CH light activation
• CH/LH lights
• CH/LH lights via dipped beam/fog lights
• Correction of consumption display
• Light attenuation DRL
• Acoustic confirmation of locking/unlocking
• Soaking mirror
• Permanent position lights
• Rear cover speed threshold
• Rear cover with trailer
• Tailgate noise
• Motor fan test
• Engine oil type
• Inspection service distance
• Inspection service interval
• Multimedia restart
• Multimedia security disclaimer
• Oil change service distance
• Oil change service interval
• Warning of impending maintenance

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps SHARAN (7N) list est apparu en premier sur VAG Coding.

Purpose: Activates the green hidden menu (green menu, hidden menu, testmode, engineer mode) on Discover MIB2.

/! Warning: Making certain changes in the hidden menu may cause MIB2 to lock up or not start at all /!

For model Facelift (radio screen like Golf 7).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“S12345”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Developer mode”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value“activated”.

Restart MIB2, keep MENU button pressed until testmode menu appears

L’article Sharan (7N) – Activate the Discover hidden menu est apparu en premier sur VAG Coding.

Purpose: to deactivate the AM radio frequency on the Discover PQ (the AM radio frequency is rarely used, unlike the FM radio frequency).
For Facelift models (Mib2 screen like Golf 7).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 14

Set bit 1 “AM_disable

L’article Sharan (7N) – Disable AM frequency on Discover est apparu en premier sur VAG Coding.