Purpose : to activate GRA cruise control (retrofit).

Modification only possible after retrofitting cruise control switch and check that your multifunction steering wheel is compatible (midline or highline).

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 01 – Motor “.

4 – Click on ” Coding II (11) or Login 11 “.

5 – Then enter code 11463, then OK (Do It!)

The code 11463 is used to activate the controller, to deactivate it if necessary the code is 16167.

Line 2:

3 – Click on ” Select “, then click on ” 16 – Multifunction handwheel “.

4– Click on ” Coding – 07 “.

5 – Options: We note in the penultimate section (0xxxx?x):

0 = No regulator installed (CCS not installed)
1 = Regulator installed with 6 positions on a separate switch (CCS with 6 positions …. etc)
3 = Regulator installed with 4 positions on the blinker switch (CCS with 4 positions via Blinker Stalk)

So replace the “?” with the 3 for commodo regulator.

Line 3:

3 – Click on ” Select”, then click on ” Select “. 01 – Engine ” .

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte“5“
Check bit“5” Cruise Control System (CCS) installed

Or byte 6 bit 0

L’article Scirocco (13) – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.

Purpose: to display the amount of fuel topped up on the ODB (on-board computer).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments“.

4 – Click on “Adaptation – 10” .

5 – Select “Volume to be Replenished” from the value list.

Select ” Yes ” in the second value list.

L’article Scirocco (13) – Make-up quantity displayed on ODB est apparu en premier sur VAG Coding.

Purpose: Enables the USB port for iPhone CarPlay accounting (after activating App Connect and changing the USB and/or USB cable) for Discover MIB2 PQ (after 2015). (Retrofit)

For firmware references:
MST2_EU_VW_PQ_P02XXT

Modify MIB2 coding and adaptation to recognize the new USB port (USB connector ref 5Q0 035 726 E) for both CarPlay and USB multimedia playback. A coding device is to be modified on the connector.

>- Activation App Connect CarPlay Android Auto

– > USB / AUX socket VW Golf 7 CarPlay Media MIB2 5Q0 035 726 E on VAG Custom


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Coding- 07” then click on“Long Coding Helper“.

5 – Select byte“19“
Then check Bit“6-7” (C0 USB Configuration: USB and iPhone Functionality)

Line 2 (optional) :

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interface for external media activation – connection 1“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “activated“

L’article Scirocco (13) – Enable USB port for iPhone CarPlay (retrofit) est apparu en premier sur VAG Coding.

Purpose: Allows you to display another logo at launch, and a color to match the finish of your Discover PQ.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte“18”
Then modify the hexadecimal value of the box in“3)” of the long code:

00 – Default
01 – Hybride
02 – GTD
03 – GTI (red color)
04 – Blue Motion
05 – E- (electric)
06 – R-Line
07 – R (blue color)
08 – Alltrack
09 – GTE

If you have a bit 0-7 drop-down list, select your vehicle or modify the byte directly with the list. If your bits are hidden, modify in the binary value :

L’article Scirocco (13) – Change Discover start logo est apparu en premier sur VAG Coding.

Purpose: to change the vehicle image of the OPS (parking aid) on the RCD 510/330/360/440 and RNS 315/510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding 07” then “Long Coding Helper”.

5 – Select Byte 6 or 9

Select the vehicle from the drop-down menu:

00 = via CAN
01 = Polo 6R
02 = New Beetle
03 = New Beetle Cabrio
04 = Scirocco
05 = Golf 5
06 = Jetta
07 = Golf 6 Variant
08 = Golf 6 Cabrio
09 = Touran
0A = Golf Plus
0C = Tiguan
0D = Sharan
0E = EOS
0F = Passat 3C
10 = Passat Limousine
11 = Passat Variant
13 = Caddy
14 = T5
2C = Skoda Octavia
2D = Skoda Octavia Kombi
2E = Skoda Superb Kombi

For the aftermarket RCD 330 (original Passat or Jetta image) for the Scirocco image:
Byte 6
Uncheck all boxes (normally only bit 0 and bit 2 are checked)

Exit the module and save your changes. The RCD or RNS must now be restarted for the changes to take effect. Press both arrows and the star for 6s.

L’article Scirocco (13) – Changing the image of the RCD/RNS OPS est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Scirocco (13) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: Allows you to disable / remove MirrorLink from App-Connect on the MIB Discover PQ. The Mirrorlink service is no longer available since June 1, 2020 on Android natively. For direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Scirocco (13) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: To activate the reversing camera after installation on the RCD 510/330/360/440 and RNS 315/510 or Discover PQ (retrofit).


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

RCD/RNS :

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 3
Then check bit 6 “Rear View Camera (RVC) installed/active”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Assistance Stationn”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 0
Then check bit 5 “Rear View Camera installed”.

Discover PQ:

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte 19
Then check bit 4 “Rear View Camera (RVC) Low installed (PR-KA1)”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Parking assistance”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 02
Then bit 4-5 select “10 Camera Type: Rear View Camera (RVC) installed”.

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Scirocco (13) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose : to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 ( For models before 2010 ! )

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

5 – The third and fourth coding digits (xx??x0x) are used to modify Instrument module options. To remove the brake pad indicator, subtract 01 from these digits.

In the example above, the initial coding is: 0027103

To delete the platelet indicator, simply recode as follows: 0026103 (27 – 01 = 26)

To activate the wafer indicator: +01

Line 2 ( For models after 2010 ! )

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Scirocco (13) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose : to deactivate the windshield washer indicator on the ODB (on-board computer).

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 ( For models before 2010 ! )

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

5 – The third and fourth coding digits (xx??x0x) are used to modify Instrument module options. To remove the ice-washer indicator, subtract 04 from these digits.

In the example above, the initial coding is: 0027103

To remove the windscreen washer indicator, simply recode as follows: 0023103 (27 – 04 = 23)

To activate the ice washer indicator: +04

Line 2 ( For models after 2010 ! )

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Scirocco (13) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.