Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights are switched on and off immediately with the headlights. Activating this function will cause a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior lighting-KL58 Einschalten mit Rampe”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article Polo 5 (6C) – Activation of progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: Allows you to disable / remove MirrorLink from App-Connect on MIB Discover. The Mirrorlink service is no longer available since June 1, 2020 on Android natively. For direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Polo 5 (6C) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 4

Disable bit 7 “Brake Pad Wear Sensor installed”

Restart the vehicle so that the warning light is no longer displayed.

L’article Polo 5 (6C) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the beep when reverse gear is engaged or when parking assistance is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Tonalité d’activation de l’aide au stationnement ” / “Park assist activation tone ” / “Aktivierungston für Einparkhilfe ” from value list

7 – Select “Off” in the second value list

L’article Polo 5 (6C) – Deactivation of parking aid activation beep est apparu en premier sur VAG Coding.

Purpose: To deactivate the “Check Distance!” / “Please check surroundings” / “Look! Safe to move?” message which appears on Discover when parking in reverse.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“03 – ABS brakes”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 01

Disable bit 5

L’article Polo 5 (6C) – Disable OPS warning message est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Volkswagen Polo 5 (6C)
–> Buy your OBDeleven device with VAG Custom

VW Polo 5 (6C) Facelift (2014-2017) / Polo 5 GTI

• Central locking with IGN
• DRL parameters in main unit
• DRL disabled with handbrake
• Electronic stability control
• Gauge test – Needle sweep
• Inspection service reset
• Stopwatch
• Acoustic confirmation of locking/unlocking
• MirrorLink on the move
• Oil service reset
• Open door alarm
• Remote trunk release
• Scandinavian DRL
• Seat belt warning
• Soundaktor
• Static bend lights
• Traction control
• Video in motion
• Remote window operation
• Automatic locking
• Basic transmission settings
• Brake lights with door open
• Bulb diagnostics: front fog lamps
• Comfort turn signals
• Correction of consumption display
• DRL on with parking lights
• DRL with low beam
• Emergency brake lights
• Motor fan test
• Front fog lights in reverse
• Fuel system priming
• Gauge test – Needle sweep V2
• Headlamp washer
• Headlamp washer activation count
• Headlamp washer activation Delay
• Headlamp washer activation time
• Turn signals with comfort windows
• Parking lights on both sides
• Power steering activation
• Fuel quantity
• The horn is always ready for use
• Disabling the Start/Stop system
• Third brake light with lock/unlock function
• Accelerator pedal response
• TPMS reset
• Radio AM
• Burglar alarm system
• Battery capacity
• Battery type
• Brake control when using ACC
• Brake light test
• Stop lights when trunk is open
• Brake lights with tail lights
• Type of CH light activation
• CH/LH light function
• CH/LH light variant
• Time to return home
• Compass position on dashboard
• Turn signal dimming rate
• Digital speed on dashboard
• Door lock test
• Driving school mode
• DRL as cornering light
• DRL function with flashing light
• DRL lights in reverse
• DRL on with AUTO
• DRL with fog lights
• Engine oil type
• Fan level display when AUTO
• Fog lamps with high beam
• Fog lamps with lights on Door
• Fog lights with turn signal
• Floor lighting
• Brightness of floor lights
• Floor lighting while driving
• Floor with blinker
• Left front door lock test
• Urban Joke” front racing car turn signals
• Right front door lock test
• Green engineering menu
• Emergency switch brightness
• Headlamp washer test
• High beam without ignition
• High-intensity brake lights
• Hill-start assist
• Hill-start assist settings
• Enhanced engine responsiveness
• Inspection service distance
• Inspection service interval
• Interior lighting discoloration
• Departure time
• LED brake lights
• LED daytime running lights
• LED front parking lights
• LED front turn signals
• LED license plate lamps
• LED low beam
• LED rear fog lights
• LED rear parking lights
• LED rear turn signals
• LED reversing light
• License plate lights with DRL
• License plate lights with trunk open
• Light sensor sensitivity
• Flashing lock button with safety light
• Low ambient temperature warning
• Rear-view mirror turn signal with high beam Beam
• Rear-view mirror indicators with CH/LH
• Multimedia restart
• Multimedia security notice
• Multimedia start logo
• Multimedia theme
• Oil change service distance
• Oil change service interval
• Oil temperature display
• Optical parking system
• Park assist activation tone
• Parking assistance audio volume reduction
• Parking assist deactivation speed
• Power steering assistance
• Rear fog light warning
• Left rear door lock test
• Right rear door lock test
• Automatic rear wiper activation
• Back-up light test
• Warning of impending maintenance
• Management response
• Rear lights when trunk is open
• Teardrop wipe
• Third brake light with CH/LH lights
• Turn signal test
• Turn signals when trunk is open
• Turn signals with CH/LH
• American-style turn signals
• American-style turn signals with DRL
• XDS interaction

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps POLO 5 (6C) list est apparu en premier sur VAG Coding.

Purpose: deactivates or activates the horn when the ignition is off.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Additional functions – Signalhorn ohne KL 15”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, choose“not active” to deactivate it or “active” to activate it, then confirm.

L’article Polo 5 (6C) – Deactivate horn without ignition est apparu en premier sur VAG Coding.

Purpose: to display a compass on the ODB (on-board computer), if you have GPS navigation (NAV), and to change its position on the speedo.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“10”
Then check Bit“6”.

Line 2 (if line 1 unavailable) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. In this drop-down menu, select the “Navigation /Compass” channel.

6 – In the “Value:” option, select“Enabled”.

Line 3 (to change the compass position on the ODB) :

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu. From this drop-down menu, select the “Compass indicator” channel.

6 – In the “Value:” option, select the desired value for the compass position on the ODB (default: lower position).

L’article Polo 5 (6C) – Compass display on ODB est apparu en premier sur VAG Coding.

Purpose: Displays the “Think Blue Monitor” mode: “ECO MODE” graph for MIB2.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_user_eco_rating”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_user_eco_rating_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

L’article Polo 5 (6C) – Activate “Think Blue Monitor” mode on Discover V2 est apparu en premier sur VAG Coding.

Purpose: to activate Coming / Leaving Home without the light sensor.


Warning! There are 5 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Comfort illumination-Coming Home Verbaustatus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, (2 choices) :

• Select the“manual” value: You will have to make a headlight flash before exiting “pulled towards you”.
• Select the“automatic” value: the headlamps will come on every time you open the driver’s door “See (5)”.

Then validate.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Comfort illumination-Menuesteuerung Coming Home Werkseinstellungz”.

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On this, select the“active” value: To display the CH/LH settings in the car radio.
Then confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Comfort illumination-Menueeinstellung Cominghome 10 s”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, enter the desired value for a duration between“0” and“60” – The value is expressed in seconds.
Then confirm.


Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Comfort illumination-Coming Home Leuchten Low beam/fog light”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, set the value to“Low beam” for low-beam headlamps and“Fog Light” for fog lamps.


Line 5:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Comfort illumination-Coming-home Einschaltereignis Driver door/ Ignition Key”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, (2 choices) :

• Select the“driver door” value to enable CH/LH when the driver door is opened.
• Select“Ignition key” to enable CH/LH on key removal.

Then validate.

L’article Polo 5 (6C) – Coming / Leaving Home without light sensor est apparu en premier sur VAG Coding.