Purpose : to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

The first two digits of the code (??xxxx) are used to modify the Instrument module options. To remove the brake pad indicator, subtract 01 from these digits.
Example of initial coding: 03142
To delete the platelet indicator, simply recode as follows: 02142 (03 – 01 = 02)

To activate the brake pad indicator: +01

L’article Polo 3 (6N) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Volkswagen Polo 3 (6N)
–> Buy your OBDeleven device with VAG Custom

VW Polo 3 (6N) (1994-2002) / VW Polo 3 Facelift (1999-2002)

• Oil service reset
• Brake pad wear indicator
• Instrument cluster region
• Seat belt warning

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps POLO 3 (6N) list est apparu en premier sur VAG Coding.

Purpose : To suppress the audible alarm and the warning light on the speedometer when driving without a seatbelt.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

The first two digits of the code (??xxxx) are used to modify the Instrument module options. To suppress the belt alarm, subtract 2 from these digits.
Example of initial coding (with belt alarm): 03142
To delete the belt alarm, simply recode as follows: 01142 (03 – 02 = 01)

L’article Polo 3 (6N) – Delete belt alarm est apparu en premier sur VAG Coding.

Purpose : to configure the keys to be used with the vehicle.

WARNING: This procedure does not configure keys with immobilizer.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 (“Remote Control Adaptation” in the drop-down list)

Enter the number of keys to be adapted. Save.
Now press button 1 or 2 on each remote control to be adapted for at least 1 second. (A horn beep will confirm the procedure).
All keys must be adapted in a single procedure.
Configuration of all keys should not exceed 15 sec.

L’article Polo 3 (6N) – Key configuration est apparu en premier sur VAG Coding.

Purpose: Resets the configuration of all keys.

ATTENTION: No more keys will be recognized with the vehicle.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set value to 0 and save

L’article Polo 3 (6N) – Reset keys est apparu en premier sur VAG Coding.

Purpose : to configure automatic door unlocking when the ignition key is removed.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 04 (“Auto-Unlock” in drop-down list)

Set value 1

L’article Polo 3 (6N) – Automatic door unlocking est apparu en premier sur VAG Coding.

Purpose : To configure automatic door locking at speeds over 15 km/h.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 03 (“Auto-Lock” in drop-down list)

Set value 1

L’article Polo 3 (6N) – Automatic door locks est apparu en premier sur VAG Coding.

But : Permet de sélectionner le type d’ouverture des portières après appui sur la télécommande.

Sélectif: un appui déverrouille uniquement la portière conducteur, deux appuis déverrouille toutes les portières.
Toutes les portières: un appui déverrouille toutes les portières.

Coding depends on number of doors and number of power windows

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on ” Coding- 07“.

2 doors / 2 electric windows
selective: set value to 00064
all doors: set value to 00065

4 doors / 2 power windows
selective: set value to 00066
all doors: set value to 00067

4 doors / 4 power windows
selective: set value to 00258
all doors: set value 00259

L’article Polo 3 (6N) – Selective unlocking / all doors est apparu en premier sur VAG Coding.

Purpose : activates turn signals when vehicle is unlocked.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 08 (“Unlocking Confirmation (Blink)” in the drop-down list)

Set value 1

L’article Polo 3 (6N) – Confirmation of vehicle unlocking (turn signals) est apparu en premier sur VAG Coding.

Purpose : activates turn signals when vehicle is locked.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 09 (“Locking Confirmation (Blink)” in the drop-down list)

Set value 1

L’article Polo 3 (6N) – Vehicle lock confirmation (turn signals) est apparu en premier sur VAG Coding.