Purpose: to activate closing and opening of the windows and sunroof with the remote control WITHOUT remaining pressed until the windows are completely closed.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Central Conv”. 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on “Coding 07” then “Long Coding Helper”

5 – Byte 6:
Bit 6: Check “Comfort Function automatic Closing”.

• Uncheck “Comfort function power windows/sunroof via remote control inactive”.
• Check “Comfort opening power windows via remote control active”.
• Check “Comfort closing power windows via remote control active”.
• Check “Closing sunroof via remote control active” (sunroof)

Line 2:

3 – Click on “Select”, then click on “46 – Module Confort”.

4– Click on “Adaptation – 10”.

Channel 17 (Comfort function)

Set value to 1

Pressing the remote control’s close button for 3 seconds will first lock the doors and then close the windows, without having to keep the button pressed until they are fully closed.

L’article Passat (B6) – One-touch window closure est apparu en premier sur VAG Coding.

Purpose: Used to adjust ambient lighting intensity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on “Select” then click on “09 – Cent. Elect.” .

4 – Click on “Adaptation 10”.

5 – Select Channel 05 (Footwell Lightning Dimming)

6 – Select intensity from 20 to 100% (in 1% increments)

L’article Passat (B6) – Ambient light intensity est apparu en premier sur VAG Coding.

Purpose : to adjust the hardness of the power steering for a softer or harder steering wheel.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.

4 – Click on“Adaptation – 10”.

5 – Select Channel 1 , set a value between 1 and 15 depending on your hardness preference.

Or Line 2: (If channel 1 is unavailable):

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.”

4– Click on“Coding – 07”.

5 – Select :

• xxx1x for smooth steering
• xxx2x for sports management
• xxx3x for hard steering
• xxx4x for harder steering
• xxx5x for very hard steering

L’article Passat (B6) – Modifying power steering hardness est apparu en premier sur VAG Coding.

Purpose: to set the length of time the headlights remain on after the car is unlocked.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select” then click on “09 – Cent. Elect.” .

4 – Click on “Adaptation – 10”.

5 – Select Channel 02 (Leaving-Home Time)

6 – Select duration from 0 to 60 sec (in 1sec increments).

L’article Passat (B6) – Leaving Home duration setting est apparu en premier sur VAG Coding.

Purpose: to set the operating time for mirror and rear window defrosting.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select” then click on “09 – Cent. Elect.” .

4 – Click on “Adaptation – 10”.

5 – Select Channel 03 (Rear Window & Outside Mirror Heater Activation Time)

6 – Select duration from 1 to 254 min (in 1 min increments).

L’article Passat (B6) – Defrost time setting est apparu en premier sur VAG Coding.

Purpose: Set the length of time the headlights remain on after the car is locked.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select” then click on “09 – Cent. Elect.” .

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 (Coming-Home Time)

6 – Select duration from 0 to 60 sec (in 1sec increments).

L’article Passat (B6) – Coming Home time setting est apparu en premier sur VAG Coding.

Purpose: to set the duration of headlamp washer activation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select” then click on “09 – Cent. Elect.” .

4 – Click on “Adaptation – 10”.

5 – Select Channel 04 (Headlight Washer Activation Time)

6 – Select duration from 50 to 10000 ms (in 50ms increments).

L’article Passat (B6) – Headlight washer duration setting est apparu en premier sur VAG Coding.

Purpose: to activate the speed governor after retrofitting.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 01 – Motor “.

4 – Click on ” Access – 11 ” then enter the code ” 11463 ”

Line 2:

3 – Click on ” Select”, then click on ” 16 – Steering Wheel“.

4 – Click on ” Coding – 07 ” then

The penultimate digit (0xxxx?x) is used to configure the cruise control.
Enter 2 if you don’t have an on-board computer
Set 4 if you have an on-board computer

.

L’article Passat (B6) – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Volkswagen Passat (B6)
–> Buy your OBDeleven device with VAG Custom

VW Passat B6 (3C) (2005-2010)

• Activate Bluetooth RNS315
• Air recirculation memory
• Automatic locking/unlocking
• Brake pad replacement
• Central locking with IGN
• Central locking
• CH/LH lights
• Change language
• Take-home mode
• Time to return home
• Bending lights
• Daytime running lights
• Driver’s seat heating memory
• DRL parameters
• Easy entry
• Emergency brake lights
• Floor lighting
• Headlamp washer
• Heating test
• Unlocking the heater
• Instrument cluster region
• Departure time
• Acoustic confirmation of locking/unlocking
• MirrorLink on the move 1
• MirrorLink on the move 2
• Oil service reset
• PTT button options
• CD lock RNS 310/315
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 SDS reversing camera
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• 510 Speed threshold
• RNS 510 theme
• Synchronized mirror adjustment
• Drop-shaped rear wiper
• Turn signals as position lights
• Window and mirror heater activation time
• Oil change interval setting
• Comfort flashers
• Seat belt warning
• Windshield washer fluid warning
• Engine oil type
• Seat belt warning V2

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps PASSAT list (B6) est apparu en premier sur VAG Coding.

Purpose: to deactivate/activate the electric handbrake in maintenance mode in order to change/replace the rear brake pad/disc linings. (EPB reset / Lining change mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


To start, set the gear lever to P, remove the electric handbrake on the button and preferably connect a battery charger according to the vehicle manual. Check that there are no faults/errors before starting basic setup.

3 – Click on“Select” then click on“53 – Parking Brake”.

4 – Click on“Basic setting – 04”.

5 – Select Channel 007

6 – Click on“Go”.

Basic Settings: OFF during the procedure, then ON when finished (yellow arrow).

A fault message will appear on your ODB indicating“Parking brake fault” and an LED in the parking brake switch, but this is normal and should be ignored.

7 – Once finished, go back (Done, Go Back) until the program closes.

8 – Switch off the vehicle’s ignition, then disconnect the VAG-COM cable

9 – Change the linings on both sides!

To reactivate the electric handbrake :


10 – With engine off and ignition switched off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

11 – Switch on the ignition and run the VCDS program.

12 – Click on“Select” then click on“53 – Parking Brake”.

13 – Click on“Basic setting – 04”.

14 – Select Channel 006

15 – Click on“Go”.

Basic Settings: OFF during the procedure, then ON when finished (yellow arrow).

16 – Once finished, go back (Done, Go Back) until the program is closed.

17 – Switch off the ignition and disconnect the VAG-COM cable.

L’article Passat (B6) – Deactivate/activate electric handbrake for rear brake pad change est apparu en premier sur VAG Coding.