Purpose: to set confirmation of door locking/unlocking with beep (alarm) or horn.

SFD: yes

Watch out! There are 5 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittierton_global“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.


Line 2:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Akustische Quittieringsdauer Einfachhorn”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this, choose“normal” or“kurz” (for a short signal), then confirm.


Line 3:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittungston_hmi_einstellbar“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittierungston_bei_entriegeln“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 5:

3 – Click on“Select” then click on “.19 – Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV Quittierungen – Quittungs_ton_bei_verriegen“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article ID.4 (E2) – Door lock/unlock confirmation (beep/horn) est apparu en premier sur VAG Coding.

Purpose: to unlock the limitations of Android Auto, allowing access to all functions without the restrictions imposed by default on the multimedia system.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.8125 – Application Server Infotainment“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“nhtsa_properties – nhtsa limitation switches for androidauto no text input”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

Line 2:

3 – Click on“Select” then click on “.8125 – Application Server Infotainment“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“nhtsa_properties – nhtsa limitation switches for androidauto no voice input”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“not_activated” and confirm.

L’article ID.4 (E2) – Unlock Android Auto limitations est apparu en premier sur VAG Coding.

Purpose: automatically activates the high beam assistant on start-up if it was active before the ignition was switched off.

SFD: yes


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“19 – Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“High Beam Assistance – Fernlichtassistent Reset“.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“not active” and confirm.

L’article ID.4 (E2) – Light Assist always active est apparu en premier sur VAG Coding.

Purpose: Enables you to unlock certain multimedia system menus while driving, which are normally blocked when the vehicle is in motion.

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.8125 – Application Server Infotainment“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Locked menu contents“.

7 – On this same page is a second drop-down menu, but at the bottom
of the page.
On this, choose“non_blocked” then validate.

L’article ID.4 (E2) – Unlock menus while driving est apparu en premier sur VAG Coding.

Purpose: to display fan speed when automatic climate control mode is activated (Climatronic fan speed display Auto mode / works with touch-sensitive climate control).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC”.

4 – Unlock SFD protection.

5 – Click on ” Adaptation – 10 “.

6 – Select ” blower display in auto operation ” in the value list

7 – Select ” activated ” from the second value list

L’article ID.4 (E2) – Display of fan speed on A/C in Auto mode est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights are switched on and off immediately with the headlights. Activating this function will result in a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

SFD: yes

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Suchbeleuchtung_allgemein – KL58 Einschalten mit Rampe“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article ID.4 (E2) – Activation of progressive interior lighting est apparu en premier sur VAG Coding.

Purpose: to deactivate the daytime running lights (DRL) using the handbrake.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.19- Gateway“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Daytime running lights-Tagfahrlicht Dauerfahrlicht bei Handbremse abschalten“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article ID.4 (E2) – Daytime running light deactivation (DRL) with handbrake on est apparu en premier sur VAG Coding.

Purpose: Adjusts the sensitivity of the light sensor.

SFD: yes

Procedure:
1– Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or your OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

3 – Click on “Select”, then click on “09 – Cent. Elect.”.

4 – Unlock SFD protection.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “RLS_Night_Sensitivity – p_lx_rs_dawn”.

7 – On this same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, choose the sensitivity value in lux, then confirm. (default: 200 lx) (the lower the value, the sooner the headlights come on).

L’article ID.4 (E2) – Set light sensor sensitivity est apparu en premier sur VAG Coding.

Purpose: Selects the speed at which the radar and/or reversing camera are deactivated.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select”, then click on“76 – Assistance stationnt“.

4 – Unlock SFD protection.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Switch-off speed for parking assist“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“15” km/h, depending on your preference.

L’article ID.4 (E2) – Speed of radar (or reversing camera) deactivation est apparu en premier sur VAG Coding.

Purpose: to deactivate the beep when reverse gear is engaged or when parking assistance is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket or your OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on ” Select” then click on ” 76 – Assistance stationnt ” .

4 – Unlock SFD protection.

5 – Click on ” Adaptation – 10 “.

6 – Select ” Tonalité d’activation de l’aide au stationnement ” / ” Park assist activation tone ” / ” Aktivierungston für Einparkhilfe ” from value list

7 – Select ” Off” in the second value list

L’article ID.4 (E2) – Deactivation of parking aid activation beep est apparu en premier sur VAG Coding.