Purpose : to activate GRA cruise control (retrofit).

Modification only possible after retrofitting cruise control switch and check that your multifunction steering wheel is compatible (midline or highline).

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 01 – Motor “.

4 – Click on ” Coding II (11) or Login 11 “.

5 – Then enter code 11463, then OK (Do It!)

The code 11463 is used to activate the controller, to deactivate it if necessary the code is 16167.

Line 2:

3 – Click on ” Select “, then click on ” 16 – Multifunction handwheel “.

4– Click on ” Coding – 07 “.

5 – Options: We note in the penultimate section (0xxxx?x):

0 = No regulator installed (CCS not installed)
1 = Regulator installed with 6 positions on a separate switch (CCS with 6 positions …. etc)
3 = Regulator installed with 4 positions on the blinker switch (CCS with 4 positions via Blinker Stalk)

So replace the “?” with the 3 for commodo regulator.

Line 3:

3 – Click on ” Select”, then click on ” Select “. 01 – Engine ” .

4 – Click on“Coding – 07” then click on“Long Coding Helper“.

5 – Select byte“5“
Check bit“5” Cruise Control System (CCS) installed

Or byte 6 bit 0

L’article Caddy (2K) Facelift – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.

Purpose: to display fan speed when automatic air-conditioning mode is activated. (Climatronic fan speed display Auto mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“11”
Then check Bit“6”:“Blower Status Display in Auto-Mode active”.

L’article Caddy 4 (2K) – Fan speed display on air conditioning in Auto mode est apparu en premier sur VAG Coding.

Purpose: Adjusts the sensitivity of the light sensor.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “2 EPIRBs” module from the drop-down list and click on “Long coding wizard”:

Byte 2:
Bits 0-7 (187, 205 or 237 to increase sensitivity, or 45, 40 or 33 to decrease sensitivity)

L’article Caddy (2K) – Adjust light sensor sensitivity est apparu en premier sur VAG Coding.

Purpose : to adjust the hardness of the power steering for a softer or harder steering wheel.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.

4 – Click on“Adaptation – 10”.

5 – Select Channel 1 , set a value between 1 and 15 depending on your hardness preference.

Or Line 2: (If channel 1 is unavailable):

3 – Click on“Select” then click on“44 – Direction assistée” / “44-steering assist.”

4– Click on“Coding – 07”.

5 – Select :

• xxx1x for smooth steering
• xxx2x for sports management
• xxx3x for hard steering
• xxx4x for harder steering
• xxx5x for very hard steering

L’article Caddy (2K) – Modify power steering hardness est apparu en premier sur VAG Coding.

Purpose: activates brake lights in flash mode during emergency braking.

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 17:
Bit 0: Check “Emergency Brake Flash Light active”.

L’article Caddy (2K) – Flash mode lights during emergency braking est apparu en premier sur VAG Coding.

Purpose : to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

5 – The third and fourth coding digits (xx??x0x) are used to modify Instrument module options. To remove the brake pad indicator, subtract 01 from these digits.

In the example above, the initial coding is: 0027103

To delete the platelet indicator, simply recode as follows: 0026103 (27 – 01 = 26)

To activate the wafer indicator: +01

L’article Caddy (2K) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: To deactivate the burnt-out bulb indicator on the ODB (on-board computer). After adding LEDs, your on-board computer may indicate that the replaced bulb is out of order.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 18 Bit 0: Uncheck “Cold Diagnosis License Plate Lights active” for plates

the other bits for the other bulbs of your choice (see image)

Byte 19 Bit 1: uncheck “Cold Diagnosis Front Parking Lights active” for night lights

Or for all bulbs:

Byte 2 Bit 2: Cold Lamp Diagnosis Active

Eliminate burnt-out bulb errors after coding.

L’article Caddy (2K) – Deactivate burnt-out bulb display est apparu en premier sur VAG Coding.

Purpose: to deactivate permanently switched-on low-beam headlamps, which are only activated when set to Auto, and to have only parking lights on during the day. (Disable Scandinavian Mode)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module from the drop-down list and click on “Long coding wizard”:

Byte 0 Uncheck Bit 3

L’article Caddy (2K) – Permanent headlamp deactivation (Scandinavian) est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the on-board computer.

Modification only possible on Mid/High range models.
Note: modifications affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel 03 “Consumption Correction”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96

L’article Caddy (2K) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: to activate the speed governor after retrofitting.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “01 – Motor”.

4 – Click on “Access – 11” then enter the code “11463”

Line 2:

3 – Click on “Select”, then click on “16 – Steering Wheel”.

4 – Click on “Coding – 07” then

The penultimate digit (0xxxx?x) is used to configure the cruise control.
Enter 2 if you don’t have an on-board computer
Set 4 if you have an on-board computer

.

L’article Caddy (2K) – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.