Purpose: Enables the USB port for iPhone CarPlay accounting (after activating App Connect and changing the USB and/or USB cable) for Discover MIB2 PQ (2015/2016). (Retrofit)

For firmware references:
MST2_EU_VW_PQ_P02XXT

Modify the MIB2 coding and adaptation to recognize the new USB port (USB connector ref 5Q0 035 726 E) for both CarPlay and USB multimedia playback. A coding pin on the connector needs to be modified.

-> Activation App Connect CarPlay Android Auto

– > USB / AUX socket VW Golf 7 CarPlay Media MIB2 5Q0 035 726 E on VAG Custom


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Coding- 07” then click on“Long Coding Helper“.

5 – Select byte“19“
Then check Bit“6-7” (C0 USB Configuration: USB and iPhone Functionality)

Line 2 (optional) :

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interface for external media activation – connection 1“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “activated“

L’article Beettle (5C) – Enable USB port for iPhone CarPlay (retrofit) est apparu en premier sur VAG Coding.

Purpose: to change the vehicle image of the OPS (parking aid) on the RCD 510/330/360/440 and RNS 315/510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding 07” then “Long Coding Helper”.

5 – Select Byte 6 or 9

Select the vehicle from the drop-down menu:

00 = via CAN
01 = Polo 6R
02 = New Beetle
03 = New Beetle Cabrio
04 = Scirocco
05 = Golf 5
06 = Jetta
07 = Golf 6 Variant
08 = Golf 6 Cabrio
09 = Touran
0A = Golf Plus
0C = Tiguan
0D = Sharan
0E = EOS
0F = Passat 3C
10 = Passat Limousine
11 = Passat Variant
13 = Caddy
14 = T5
2C = Skoda Octavia
2D = Skoda Octavia Kombi
2E = Skoda Superb Kombi

Exit the module and save your changes. The RCD or RNS must now be restarted for the changes to take effect. Press both arrows and the star for 6s.

L’article Beetle (5C) – Change the RCD/RNS OPS image est apparu en premier sur VAG Coding.

Purpose: Allows you to disable the AM radio frequency on the Discover PQ (the AM radio frequency is rarely used, unlike the FM radio frequency).
For Beetle Facelift after 2015 (Radio screen like Golf 7).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 14

Set bit 1 “AM_disable

L’article Beetle (5C) – Disable AM frequency on Discover est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Beetle (5C) – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: Allows you to disable / remove MirrorLink from App-Connect on the MIB Discover PQ. The Mirrorlink service is no longer available since June 1, 2020 on Android natively. For direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Beetle (5C) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Beetle (5C) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to activate voice control on the RNS 510 (SDS).

ATTENTION: RNS 510 firmware must be version v2660.

Activating voice control brings up the “Voice control” menu in the RNS 510’s SETUP menu.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3, check the box for“Bit 1: Microphone Diagnostics active”.

Byte 7, uncheck the box for“Bit 1: Voice Control inactive”.

To install the microphone, connect the microphone lead to the rear of the RNS 510. Connect to pins (Mic-)C1 and (Mic+)C7.

L’article Beetle (5C) – Activate RNS 510 voice control est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Volkswagen Beetle (5C)
–> Buy your OBDeleven device with VAG Custom

VW Beetle 3 Beetle (5C) (2011-2019)

• Gauge test – Needle sweep
• Inspection service reset
• Oil service reset
• CD lock RNS 310/315
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 reversing camera
• SDS RNS 310/315
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• Speed limit RNS 510
• RNS 510 theme
• Seat belt warning
• Automatic locking/unlocking
• CH/LH lights via dipped beam/fog lights
• Bending lights
• Motor fan test
• Mirror heating with rear window
• Teardrop wipe
• Activating Bluetooth RNS315
• ATWS country setting
• Automatic rear lid lock
• Central locking with IGN
• Central lock settings
• CH/LH lights
• Comfort turn signals
• Comfort windows
• Time to return home
• Correction of consumption display
• Clutch message display
• DRL Activation/Deactivation
• Emergency brake lights
• Engine oil type
• Fog lamps with high beam
• Maintenance of front wipers
• Fuel system priming
• Heated mirrors
• Hill-start assist settings
• Tilt sensor sensitivity
• Turn signals with comfort windows
• Maintenance distance
• Service interval
• Instrument cluster language
• Inside surveillance
• Sensitivity of interior surveillance
• Departure time
• LED license plate illumination
• Acoustic confirmation of locking/unlocking
• Acoustic confirmation of locking/unlocking V2
• Multifunction display
• Multimedia security disclaimer
• Oil change service distance
• Oil change service interval
• Parking light
• Telephone connection tone
• Rear wiper with reverse
• Remote trunk release
• Scandinavian daytime running lights
• Selective central locking
• Warning of impending maintenance
• Visual confirmation
• XDS interaction

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps BEETLE (5C) list est apparu en premier sur VAG Coding.

Purpose: to activate Hill Hold Control.

Hill Hold Control maintains brake pressure for a few seconds after prolonged application of the brake pedal.

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select” then click on“03 – Brains ABS” (or“03 – ABS Brakes ”).

4 – Click on“Codage- 07” then“Long Coding Helper”.

Byte 16 :
Bit 3: Tick “Hill Hold Control (HHC/PR-UG1/UG4) active/installed”.

Line 2 Hill Hold Control setting.

3 – Click on“Select” then click on“03 – Brains ABS” (or“03 – ABS Brakes ”).

4 – Click on“Adaptation – 10”.

Select Channel 58 (Hill Hold Control (HHC) from the drop-down list)

Choose a value
0 “normal”
1 “earlier” (restarts with lower acceleration)
2 “later” (restarts with higher acceleration)

L’article Beetle (5C) – Hill Hold Control est apparu en premier sur VAG Coding.

Purpose: to activate the electronic differential lock (XDS).

The electronic differential lock (XDS) is an extension of the well-known EDS function. However, XDS does not react to acceleration slip, but rather relieves pressure on the inside front wheel when cornering. XDS applies pressure to the inside wheel during cornering from the hydraulic ESP to prevent slippage.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “03 – ABS”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

Byte 17 :
Bit 3: Tick “(Extended) Electronic Differential Lock (XDS – PR-UG3/UG4) active/installed”

Line 2 XDS setting.

3 – Click on “Select”, then click on “03 – ABS”.

4 – Click on “Adaptation – 10 ”.

Channel 36 (Electronic Differential Lock (XDS) in drop-down list)

Choose a value
0“medium”
1 “low”
2 “high

L’article Beetle (5C) – Electronic differential lock (XDS) est apparu en premier sur VAG Coding.