Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-side activation via the turn signal switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Außenlicht_uebergreifend-Parklicht ueber LSS aktiviert”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Bilateral” and confirm.

L’article Arteon (3H) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Arteon (3H) – Front Assist settings est apparu en premier sur VAG Coding.

Purpose: deactivates sound reduction when reverse gear is engaged or parking aid is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Demande réduction audio ” / “Audio attenuation request” / “Anforderung Audioabsenkung ” from the value list.

7 – Select “Off” in the second value list

L’article Arteon (3H) – Disable parking aid audio reduction est apparu en premier sur VAG Coding.

Purpose: turns on license plate illumination when trunk / tailgate is open.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte 25KZL HA59 – Lichtfunktion C 25”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, choose the value“Heckdeckel Offen” and confirm. (origin : nicht aktiv)


Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Leuchte 25KZL HA59 – Dimmwert CD 25

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“100” and confirm. (origin : 0)

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte25KZL HA59 – Dimming Direction CD 25”.

7 – On this same page, there is a second drop-down menu, but towards the bottom
of the page.
On the latter, choose“maximise” then validate.

L’article Arteon (3H) – Trunk-open license plate illumination est apparu en premier sur VAG Coding.

Purpose: automatically retracts the electric driver’s seat when the ignition is switched off and the door is opened (access aid).

This option can only be activated with a VCDS with experimental coding for the lo coding wizard.ng! (MIB2 compatible)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on “.36 – Seat Mem. Drvr“.

4 – Click on“Coding 07”.

5 – Select “Long coding wizard”:

Byte 3, Set bit 1 – “Easy_Entry_front,0=nict aktiv/1=aktiv

For passenger seat with electric option: Byte 6, Set bit 3

Then Byte 9 Set bit 6 – “automatic_func_key_memory_over_MMI, 0=nict aktiv/1=aktiv”.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2 – driver_seat_0x10”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2 – driver_seat_0x10_msg_bus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Comfort data bus” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2 – menu_display_seat_configuration”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 5:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2 – menu_display_seat_configuration_over_threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Arteon (3H) – Easy Entry est apparu en premier sur VAG Coding.

Purpose: to correct the fuel consumption display on the Trip Computer/Virtual Cockpit.

Note: these changes affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel: “Display correction of consumptions and operating range”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96.

Example 3: the consumption announced by the ODB is 5.9l/100km, after checking it is actually 6.3l/100km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%, and the consumption announced by the ODB will be a pessimistic 0.1l/100km.

Consumption is immediately modified on the Discover MIB :

L’article Arteon (3H) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: Automatically closes windows and sunroof when it rains.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ZV KOMFORT – Regenschliessen_ein_aus”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ZV KOMFORT – Regenschliessen_art

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Permanent” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “ZV KOMFORT – Menuesteuerung Regenschliessen”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Coding – 07”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“RLFS”.

7 – Select byte“0”
Then check Bit“1”:“Rain Light Function active”
Then Bit“2”:“Rain Closing active”

–> If RLFS is inaccessible with VCDS, you must use OBDeleven :

Restart Discover

• RLHS sensor not compatible!

• If the function is correctly added: Automatic window closing in the event of rain :

With the VW Arteon, you have the option of activating the automatic window-closing function in the event of rain in the on-board network control unit.

The windows and panoramic roof are linked to the rain sensor, so the doors close automatically. The operating mode can be activated or deactivated in the CAR menu on the Discover infotainment system.

L’article Arteon (3H) – Automatic window closure in the event of rain est apparu en premier sur VAG Coding.

Purpose: to keep the 3rd brake light on if the trunk is not fully closed. For security lighting at night or to make sure your safe is securely closed.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte22BR MA57-Lichtfunktion C 22”.

7 – On this same page, there’s a second drop-down menu at the bottom
of the page.
On this, select the value“Heckdeckel Offen” and confirm. (Origin: nicht aktiv)


Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte22BR MA57-Dimmwert CD 22”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, choose a value between“0” and“100” depending on the power of the brake light, then confirm. (Origin: 0)

L’article Arteon (3H) – Third brake light on when trunk is open est apparu en premier sur VAG Coding.

Purpose: to adjust the hardness of the power steering for a softer steering wheel (Comfort) or a harder sporty one (Dynamic).
Warning: if you have the driving mode selection, do not modify!

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“44 – Steering Assistance”.

4 – Click on“Security Access – 16” then enter the code“19249”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Courbes caractéristiques d’assistance de direction” /“Characteristic curve of steering assistance”

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose the value:“Confort” or “Dynamic” then validate.

selection_by_charisma: You have the driving modes, do not modify this value otherwise you will lose the hardness of the steering wheel according to your driving mode!

L’article Arteon (3H) – Modify power steering hardness est apparu en premier sur VAG Coding.

Purpose: to modify the vehicle on the Active Info Display / Virtual Cockpit.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17- Instruments”.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“02“
Then select Bit“3-6“: ” “.Model: Variant X“

Choose the Variant corresponding to the desired vehicle.

Example of a Variant :

Variant 2: Golf 7 GTI 5-door
Variant 3: Golf 7 GTI 3-door
Variant 6: Golf 7R 5-door
Variant 7: Golf 7R 3-door

L’article Arteon (3H) – Virtual Cockpit vehicle modification est apparu en premier sur VAG Coding.