Purpose: Resets the settings for all remote controls associated with the vehicle.

WARNING: After completing this procedure, all remote controls will be deleted and will need to be reprogrammed using the “Program a Remote Control” tutorial .
If your vehicle is equipped with a KESSY remote control (05 – Access/Start Authorization), you cannot delete the remote controls using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set the value to 0 and save

L’article Amarok (2H) – Resetting the Remote Controls est apparu en premier sur VAG Coding.

Purpose: Allows you to program the remote controls that will be used with the vehicle for central locking and unlocking.

WARNING: This procedure does not allow you to program remote controls with the vehicle’s immobilizer.
If your vehicle is equipped with a KESSY remote control (05 – Access/Ignition Authorization), you cannot program a new remote control using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 ( “Remote Control Adaptation” from the drop-down list)

Enter the number of keys to program, then click Save.
Next, press the Unlock button on each remote control to be programmed for at least 1 second. The flashing lights will confirm the process.
All keys must be programmed in a single session, one after the other.
Programming all keys must not take longer than 15 seconds.
You can add up to 7 remote controls. If the [Test] and/or [Save] buttons are grayed out and unclickable, the module likely has all 7 slots filled; delete the remote controls using the “Reset Remote Controls” tutorial.

L’article Amarok (2H) – Programming a Remote Control est apparu en premier sur VAG Coding.

Purpose: to add Offroad mode to Discover PQ with navigation.


Warning! There are 3 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-compass_0x15”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_Adaptations_Gen2-menu_display_Compass_over-threshold_high”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Restart the Discover Media PQ (hold down the ON/OFF button for at least 5 seconds).

Depending on your hardware and firmware, the off-road menu may appear directly in the Menu, or it may be hidden:
Press the VOICE-MENU-NAV buttons to access the secret menu, where you’ll now find the OFFROAD screen:

L’article Amarok (2H) Facelift – Activate Off-Road mode on Discover PQ est apparu en premier sur VAG Coding.

Purpose: Allows you to disable or remove MirrorLink from App-Connect on the MIB Discover PQ. The MirrorLink service has not been natively available on Android since June 1, 2020. For a direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Amarok (2H) Facelift – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: Allows you to add a Driving School mode view to the RCD 210, RCD 310 that displays turn signals, speed … (Also ideal for accompanied driving)


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“56 – Radio”.

4 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Channel 2”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“1” and confirm.

L’article Amarok (2H) – Activate Driving School mode (RCD 210/RCD 310) est apparu en premier sur VAG Coding.

Purpose: to display fan speed when automatic air-conditioning mode is activated. (Climatronic fan speed display Auto mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“11”
Then check Bit“6”:“Blower Status Display in Auto-Mode active”.

L’article Amarok (2H) Facelift – Fan speed display on air conditioning in Auto mode est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after it has been retrofitted to the Discover PQ.

For Amarok Facelift after 2015 (Radio screen like golf 7).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Coding – 07” then click on“Long Coding Helper”.

6 – Select byte 19
Then check bit 4 “Rear View Camera (RVC) Low installed (PR-KA1)”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Parking assistance”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 02
Then bit 4-5 select “10 Camera Type: Rear View Camera (RVC) installed”.

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 pins of the reversing camera are used in the 12-pin quadlock (blue). Usable cable set: Part no. 000 979 009 E

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Amarok (2H) Facelift – Activate reversing camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: Activates the green hidden menu (green menu, hidden menu, testmode, engineer mode) on Discover MIB2.

/!\ Caution: Making certain changes in the hidden menu may cause MIB2 to freeze or no longer start /!\

For Amarok Facelift after 2015 (Radio screen like Golf 7).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“S12345”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Developer mode”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value“activated”.

Restart MIB2, keep MENU button pressed until testmode menu appears

L’article Amarok (2H) Facelift – Activate Discover hidden menu est apparu en premier sur VAG Coding.

Purpose: to deactivate the AM radio frequency on the Discover PQ (the AM radio frequency is rarely used, unlike the FM radio frequency).
For Amarok Facelift after 2015 (Radio display like Golf 7).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on “Coding – 07”.

5 – Click on “Long Coding Helper” .

6 – Select Byte 14

Set bit 1 “AM_disable

L’article Amarok (2H) Facelift – Disable AM frequency on Discover est apparu en premier sur VAG Coding.

Purpose: to activate Hill Hold Control.

Hill Hold Control maintains brake pressure for a few seconds after prolonged application of the brake pedal.

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select” then click on“03 – Brains ABS” (or“03 – ABS Brakes ”).

4 – Click on“Codage- 07” then“Long Coding Helper”.

Byte 16 :
Bit 3: Tick “Hill Hold Control (HHC/PR-UG1/UG4) active/installed”.

Line 2 Hill Hold Control setting.

3 – Click on“Select” then click on“03 – Brains ABS” (or“03 – ABS Brakes ”).

4 – Click on“Adaptation – 10”.

Select Channel 58 (Hill Hold Control (HHC) from the drop-down list)

Choose a value
0 “normal”
1 “earlier” (restarts with lower acceleration)
2 “later” (restarts with higher acceleration)

L’article Amarok (2H) – Hill Hold Control est apparu en premier sur VAG Coding.