Purpose: Allows you to disable or remove MirrorLink from SmartLink on the MIB2 PQ. The MirrorLink service has not been natively available on Android since June 1, 2020. For a direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Yeti (5L) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: Allows you to add Apple CarPlay and Android Auto to SmartLink after it has been enabled on MIB2 systems with part numbers starting with 2xxT, when only MirrorLink appears in the SmartLink menu.

For the firmware reference:
MST2_EU_SK_PQ_P02XXT

–> SmartLink Activation for CarPlay and Android Auto
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Yeti (5L) – Add CarPlay / Android Auto after activating SmartLink MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Activates the green hidden menu (green menu, hidden menu, testmode, engineer mode) on Discover MIB2.

/!\ Caution: Making certain changes in the hidden menu may cause MIB2 to freeze or no longer start /!\

For model Facelift (radio screen like Golf 7).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“S12345“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Developer mode“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value“activated“.

Restart MIB2, keep MENU button pressed until testmode menu appears

L’article Yeti (5L) – Activate hidden menu Amundsen est apparu en premier sur VAG Coding.

Purpose: Enables the USB port for iPhone CarPlay accounting (after activating SmartLink and changing the USB and/or USB cable) for MIB2s. (Retrofit)

For firmware references:
MST2_EU_SK_PQ_P02XXT

Modify the MIB2 coding and adaptation to recognize the new USB port (USB connector ref 5Q0 035 726 E) for both CarPlay and USB multimedia playback. A coding pin on the connector needs to be modified.

–> SmartLink Activation for CarPlay and Android Auto
–> USB / AUX Port for VW Golf 7 CarPlay Media MIB2 5Q0 035 726 E on VAG Custom
–> Add CarPlay / Android Auto after SmartLink MIB2 2xxT activation
–> Disable MirrorLink

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Codage- 07” then click on“Assistant Codage Long”.

5 – Select byte“19“
Then check Bit“6-7” (C0 USB Configuration: USB and iPhone Functionality)

Line 2 (optional) :

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interface for external media activation – connection 1“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “activated“

L’article Yeti (5L) – Enable USB port for iPhone CarPlay (retrofit) est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Yeti (5L) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Yeti (5L) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to activate voice control on the RNS 510 (SDS).

ATTENTION: RNS 510 firmware must be version v2660.

Activating voice control brings up the “Voice control” menu in the RNS 510’s SETUP menu.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3, check the box for“Bit 1: Microphone Diagnostics active”.

Byte 7, uncheck the box for“Bit 1: Voice Control inactive”.

To install the microphone, connect the microphone lead to the rear of the RNS 510. Connect to pins (Mic-)C1 and (Mic+)C7.

L’article Yeti (5L) – Activate RNS 510 voice control est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for Skoda Yeti (5L)
–> Buy your OBDeleven device with VAG Custom

Skoda Yeti 5L (2009-2017)

• Air recirculation memory
• Bending lights
• Driver’s seat heating memory
• ESC V2 deactivation
• Inspection service reset
• Oil service reset
• CD lock RNS 310/315
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 SDS reversing camera
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• Speed limit RNS 510
• RNS 510 theme
• Automatic locking/unlocking
• Comfort operation for sunroof
• Comfort turn signals
• Correction of consumption display
• DRL parameters
• DRL with ADL
• Hill-start assist
• Acoustic confirmation of locking/unlocking
• Permanent position lights
• Rear wiper with reverse
• Seat belt warning
• Air conditioning damper calibration
• Activating Bluetooth RNS315
• Automatic return lights
• Automatic rear lid lock
• Automatic rainfall Closing
• Brake assist parameters
• Brake lights with ignition
• Brake pad wear indicator
• Central locking with ignition
• Type of CH light activation
• CH/LH lights
• CH/LH light variant
• Comfort opening type for sunroof
• Comfort control for driver’s window
• Comfort windows
• Comfort windows via door lock
• Bending lights with reverse
• Cruise control
• Driving school mode
• DRL Gradation
• DRL in MFD+
• DRL inactive with flashing light
• DRL indicator in dashboard
• DRL OFF with handbrake
• Emergency brake flashing with trailer
• Emergency brake lights
• Motor fan test
• Engine oil type
• Brightness of floor lighting when door is open
• Floor lighting
• Floor lighting menu
• Resetting the fuel pressure regulator
• Fuel system priming
• Headlight brightness
• Headlamp washer
• Right/left-hand drive headlights
• Heating time for windows and mirrors
• Heating test
• Unlocking the heater
• Freeway lights
• Hill-hold Assist Settings
• Indicators with comfort glass
• Inspection service distance
• Inspection service interval
• Instrument cluster language
• Departure time
• LED license plate illumination
• Locking/unlocking – Horn confirmation
• Mirror scan
• Oil change service distance
• Oil change service interval
• One-touch power window settings
• Rear door exit lights
• Drop-shaped rear wiper
• Rear wiper
• Rear wiper with front wiper (interval)
• Rear wiper with front wiper (permanent)
• Selective central locking
• Synchronized mirror adjustment
• Brightness of rear lights
• Teardrop wipe
• Visual confirmation
• Washer fluid indicator
• Windows and sunroof still operational

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps YETI list (5L) est apparu en premier sur VAG Coding.

Purpose: Activates the hidden menu in RNS 510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” Select ” and run the VCDS program.56 – Radio” .

4 – Click on “Adaptation – 10”.

5 – Choose Channel 50 then set the value to 1

Restart the RNS 510.

To launch the Hidden Menu, press SETUP (for 6s)

L’article Yeti (5L) – Activate hidden menu RNS 510 est apparu en premier sur VAG Coding.

Purpose: to change the display theme of the RCD 510 and RNS 510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” for RNS510 and “56 – Radio” for RCD510.

4 – Click on“Coding 07” then “Long Coding Helper”.

5 – Select Byte 7

Bit 4-5: Select from 3 themes
“00 Display Variant: Highline
“10 Display Variant: Sportsline
“20 Display Variant: Premium

Exit the module and save your changes. The RCD / RNS 510 must now be restarted for the changes to take effect. Press both arrows and the star for 6s.

L’article Yeti (5L) – Change the RCD/RNS 510 theme est apparu en premier sur VAG Coding.