Purpose: Allows you to add Apple CarPlay and Android Auto to SmartLink after it has been enabled on MIB2 systems with part numbers starting with 2xxT, when only MirrorLink appears in the SmartLink menu.

For the firmware reference:
MST2_EU_SK_ZR_P02XXT

–> SmartLink Activation for CarPlay and Android Auto
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Superb (3V) – Add CarPlay / Android Auto after activating SmartLink MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Displays the “Driving Mode” on the Amundsen Bolero Columbus MIB2. This may need to be enabled after replacing the MIB if the driving modes are no longer available.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma_over_threshold_high“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17_msg_bus“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Infotainment data bus” and then confirm.

L’article Superb (3V) – Driving Mode on MIB2 est apparu en premier sur VAG Coding.

Purpose: to code and adapt the Touch Climatronic panel so that the AC climate control/compressor is functional after installation. (Touch Climatronic) (Retrofit)

Touch Climatronic Unit ref example: 3G8907044 / 5NA907044AJ

Tactile climate control coding

Procedure:
1– Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2– Switch on the ignition and run the VCDS program.

The coding information is found using the “Long Coding Helper” when connecting to the vehicle with VCDS. Before replacing a module, save the original coding of the original A/C module and transfer it to the new touchscreen A/C module.

Transfer old unit’s long code to new unit’s long code + Check

3 – Click on“Select” then click on“08 – Climatronic” / “08 – Auto HVAC“.

4 – Click on“Coding- 07” then click on“Long Coding Helper“.

5 – Copy the long code (1) (the 30 or so digits in yellow) (on a notepad on your PC, for example) from your original air-conditioning system, then exit VCDS and change your current air-conditioning panel to touch-sensitive, relaunch VCDS and paste the saved long code in place of the current touch-sensitive air-conditioning long code! then exit -> Go

Options :

Coding : Only if you don’t have a rear-row climate control unit, e.g. Golf 7.5 (VCDS with experimental menu only)

3 – Click on“Select” then click on“08 – Climatronic” / “08 – Auto HVAC“.

4 – Click on“Coding- 07” then click on“Long Coding Helper“.

5 – Select byte“7“
Then check Bit“2-3” [LN]_Climate zones second row of seats : [VN]_not installed : Enabled

Adaptation (option)

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC“.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ENG248446-HMI_View_Switch“.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Basic setting for air-conditioning compressor

Note: the basic setting must be made when the air-conditioning control module (J301) or the damper motor(s) have been replaced.

Adaptation of shutter end stops
Required when shutter motors are replaced or when a self-check is required for self-diagnosis of defective motors.

[Select]
[08 – Climatronic” / “08 – Auto HVAC]
[Basic settings – 04]
Select IDE01546-ENG167462 “Adapt shutter/door end stops” from the drop-down list
[Go!]
Basic setting takes about 20 seconds.
Completed correctly should be displayed
[Stop]
[Completed, Go back]
[Close controller, Go back – 06]
Clear fault codes !!!

Initial running-in of air-conditioning compressor
Required when air-conditioning control module (J301) is replaced.

Prerequisites for starting the first running-in of the air-conditioning compressor in basic mode :

• Engine idling
• Transmission in Park or Neutral position
• Do not switch off the ignition
• The basic setting has been made for the shutters
• Interior fan motor is on
• Air vents fully open
• Load management not active

Steps for the “first running-in of the air-conditioning compressor” :

1- Start the engine and let it idle.

2- Go to adaptation and change the values of these two channels to 120 s :

[Select]
[08 – Climatronic” / “08 – Auto HVAC]
[Adaptation – 10]

IDE01503-Basic setting operating time for compressor running-in, 120 s, 1 … 120 you must carry out the process/modification even if it already has the value of 120 s.
IDE03176-Compressor runtime, 60 s, 1 … 120

3- Close/quit controller/unit 08, Close/quit VCDS, Switch off motor, Wait between 30 seconds and one minute, Restart motor, Open VCDS again and re-enter unit 08, Go to adaptation and re-enter original values, 120 and 60 respectively.

4- Go to basic settings.

[08 – Climatronic” / “08 – Auto HVAC]
[Basic settings – 04]

Select IDE02259-ENG167462 “Compressor run/rod in: automatic start” from the drop-down list.
[Go!]
Wait 120 s (2 min), observe the A/C button indicator on the clim touch panel flashing.
Once the basic settings have been completed, the A/C indicator goes out and the process is finished.
[Stop]

Check fault codes. Delete if necessary. Exit Climatronic 08. Check that A/C button is working/on.

Basic setting Without VCDS :

Switch on the motor, then press AC+MENU simultaneously for 10 seconds. Please wait 2 to 3 minutes (correspondence is in progress at this time) and do not perform any irrelevant actions!
Once the process is complete, the air purification and internal circulation LEDs will work! If this does not work, please check the code and whether the motor is switched on!

Then press and hold rear window defroster + AC for 2 to 3 minutes (it will fail if you move away for a second). Be patient and try several times. If you see the AC light on, you’ve succeeded.

If the MENU button doesn’t display anything on your Discover screen :

Line 1:

3 – Click on“Select” then click on“5F – Electr. information“.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-climatic_master_0x01” and“climatic_slave_0x02” and“auxilary_heating_0x03“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 10:

3 – Click on“Select” then click on“5F – Electr. information“.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6- On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-climatic_master_0x01_msg_bus” and“climatic_slave_0x02_msg_bus” and“auxilary_heating_0x03_msg_bus“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

L’article Superb (3V) – Activate Touch Climatronic (retrofit) est apparu en premier sur VAG Coding.

Purpose: Enables the USB port for iPhone CarPlay accounting (after activating SmartLink and changing the USB and/or USB cable) for MIB2s. (Retrofit)

For firmware references:
MST2_EU_SK_ZR_P02XXT

Modify the MIB2 coding and adaptation to recognize the new USB port (USB connector ref 5Q0 035 726 E) for both CarPlay and USB multimedia playback. A coding pin on the connector needs to be modified.

–> SmartLink Activation for CarPlay and Android Auto
–> USB/AUX Port for VW Golf 7 CarPlay Media MIB2 5Q0 035 726 E on VAG Custom
–> Ajouter CarPlay / Android Auto après activation Smart Link MIB2 2xxT
–> Disable MirrorLink


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Codage- 07” then click on“Assistant Codage Long”.

5 – Select byte“19“
Then check Bit“6-7” (C0 USB Configuration: USB and iPhone Functionality)

Line 2 (optional) :

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Interface for external media activation – connection 1“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the value “activated“

L’article Superb (3V) – Enable USB port for iPhone CarPlay (retrofit) est apparu en premier sur VAG Coding.

Purpose: activates rearview mirror defrosting automatically when rear window defrosting is activated, to avoid having to move the rearview mirror switch to set defrosting, for example when in position R for reversing.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“: “Rear window heater trigger, active“


Line 2:

3 – Click on“Select”, then click on“42 – Driver’s door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“:“Rear window heater trigger, active“.

L’article Superb (3V) – Activate automatic mirror defrosting with rear window est apparu en premier sur VAG Coding.

Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-side activation via the turn signal switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Außenlicht_uebergreifend-Parklicht ueber LSS aktiviert”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Bilateral” and confirm.

L’article Superb (3V) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: enables headlight flashes to be made even when the ignition is off.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Driving light and parking light-Lichthupe bei Zuendung aus moeglich”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Superb (3V) – Contactless headlight activation est apparu en premier sur VAG Coding.

Purpose: to deactivate the Corner Lights (AFS) when reverse gear is engaged.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “static directional light-bei Rueckwaertsfahrt” / “static AFS light-bei Rueckwaertsfahrt”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
Select “Off” and confirm.

L’article Superb (3V) – Deactivation of Corner Lights when reversing est apparu en premier sur VAG Coding.

Purpose : activates xenon light kinematics when the vehicle is started. (DLA presentation)

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “55 – Headlight range”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Security Access – 16” then enter the code“20103”

5 – Click on “Adaptation – 10”.

6 – Select the “Presentation mode” in the value list

7 – Select “active” in the second list

L’article Superb (3V) – Xenon presentation mode est apparu en premier sur VAG Coding.

Purpose: to adjust the ACC distance setting from the factory setting so that it can be set in 1 km/h increments by pressing the switch.

By default, the PLUS and MINUS buttons on the adaptive cruise control system adjust your speed in 10 km/h increments. You can change the coding in 1 km/h increments by briefly pressing the button. And use the old 10 km/h speed increments by pressing and holding the buttons.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:


3 – Click on ” Select ” and then click on “Select”. 13 – Regul Dist. ” .

4 – Click on “Security Access – 16” then enter the code “14117 or 20103”.

5 – Click on “Coding – 07”.

6 – Click on “Long Coding Helper” .

7 – Select Byte 02

Select bit 6 “Operation Mode 2”.

Some speed controller modules may use a different coding or even have this parameter as an adaptation instead of the coding. Make sure that the option you are about to modify is correctly labeled.

Module 13 → Adaptation → Mode de fonctionnement / Operation Mode → Mode de fonctionnement 2 / Operation Mode 2

L’article Superb (3V) Facelift – Adjust ACC control in 1 km/h increments est apparu en premier sur VAG Coding.