Purpose: to correct the fuel consumption display on the on-board computer.

Modification only possible on Mid/High range models.
Note: modifications affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel 03 “Consumption Correction”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96

L’article Superb (3U) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose : ^To deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. for pads without a sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

The first two digits of the code (??xxxx) are used to modify the Instrument module options. To remove the brake pad indicator, subtract 01 from these digits.
Example of initial coding (with nameplate indicator): 05142
To remove the indicator plate, simply recode as follows: 04142 (05 – 01 = 04)

To activate the brake pad indicator: +01

L’article Superb (3U) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Skoda Superb (3U)
–> Buy your OBDeleven device with VAG Custom

Skoda Superb 1 (3U) (2001-2008)

• Oil service reset
• Automatic locking/unlocking
• Brake pad warning
• Change language
• Country setting for horn
• Door-open indicator
• Inside surveillance
• Acoustic confirmation of locking/unlocking
• Seat belt warning
• Selective door unlocking
• Visual confirmation
• Windshield washer fluid warning
• Engine oil type

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps SUPERB (3U) list est apparu en premier sur VAG Coding.

Purpose : Allows you to modify the type of tone and duration of the horn sound, depending on the country.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 10

Select :

1 – RoW (Rest of the World)
2 – Germany
3 – Great Britain

L’article Superb (3U) – Horn setting est apparu en premier sur VAG Coding.

Purpose : to deactivate the windshield washer indicator on the ODB (on-board computer).

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

The first two digits of the code (??xxxx) are used to modify the Instrument module options. To remove the ice-washer indicator, subtract 04 from these digits.
Example of initial coding (with washer indicator): 05142
To remove the windscreen washer indicator, simply recode as follows: 01142 (05 – 04 = 01)

To activate the ice washer indicator: +04

L’article Superb (3U) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to activate the speed governor after retrofitting.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “01 – Motor”.

4 – Click on “Access – 11” then enter the code “11463”

L’article Superb (3U) – Cruise control activation (retrofit) est apparu en premier sur VAG Coding.

Purpose : To configure automatic door locking at speeds over 15 km/h.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 03 (“Auto-Lock” in drop-down list)

Set value 1

L’article Superb (3U) – Automatic door locks est apparu en premier sur VAG Coding.

Purpose : to configure automatic door unlocking when the ignition key is removed.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “46 – Comfort Module”.

4 – Click on “Adaptation – 10”.

5 – Select Channel 04 (“Auto-Unlock” in drop-down list)

Set value 1

L’article Superb (3U) – Automatic door unlocking est apparu en premier sur VAG Coding.

Purpose : To suppress the audible alarm and the warning light on the speedometer when driving without a seatbelt.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07”.

The first two digits of the code (??xxxx) are used to modify the Instrument module options. To suppress the belt alarm, subtract 2 from these digits.
Example of initial coding (with belt alarm): 03142
To delete the belt alarm, simply recode as follows: 01142 (03 – 02 = 01)

L’article Superb (3U) – Delete belt alarm est apparu en premier sur VAG Coding.

But : Permet de sélectionner le type d’ouverture des portières après appui sur la télécommande.

Sélectif: un appui déverrouille uniquement la portière conducteur, deux appuis déverrouille toutes les portières.
Toutes les portières: un appui déverrouille toutes les portières.

Coding depends on number of doors and number of power windows

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on ” Select”, then click on ” 46 – Comfort Module“.

4 – Click on ” Coding- 07“.

2 doors / 2 electric windows
selective: set value to 00064
all doors: set value to 00065

4 doors / 2 power windows
selective: set value to 00066
all doors: set value to 00067

4 doors / 4 power windows
selective: set value to 00258
all doors: set value 00259

L’article Superb (3U) – Selective unlocking / all doors est apparu en premier sur VAG Coding.