Purpose: to change the vehicle image of the OPS (parking aid) on the RCD 510/330/360/440 and RNS 315/510.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding 07” then “Long Coding Helper”.

5 – Choose Byte 6 or 9

Selectthe vehicle from the drop-down menu:

00 = via CAN
01 = Polo 6R
02 = New Beetle
03 = New Beetle Cabrio
04 = Scirocco
05 = Golf 5
06 = Jetta
07 = Golf 6 Variant
08 = Golf 6 Cabrio
09 = Touran
0A = Golf Plus
0C = Tiguan
0D = Sharan
0E = EOS
0F = Passat 3C
10 = Passat Limousine
11 = Passat Variant
13 = Caddy
14 = T5
2C = Skoda Octavia
2D = Skoda Octavia Kombi
2E = Skoda Superb Kombi

Exit the module and save your changes. The RCD or RNS must now be restarted for the changes to take effect. Press both arrows and the star for 6s.

L’article Superb (3T) – Changing the image of the RCD/RNS OPS est apparu en premier sur VAG Coding.

Purpose: to activate the reversing camera after installation on the RCD 510/330/360/440 and RNS 315/510 (retrofit).


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“37 – Navigation” (RNS) or“56 – Radio” (RCD)

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 3
Then check bit 6 “Rear View Camera (RVC) installed/active”.

Line 2 (Option, if parking assistance available) :

3 – Click on“Select”, then click on“10 – Assistance Stationn”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte 0
Then check bit 5 “Rear View Camera installed”.

Hardware upgrade :

The camera’s video cable is connected to the infotainment control unit. It is installed in the glovebox.

The 2 rearview camera pins are used in the 12-pin quadlock (blue).

Quadblock Assignment :

Pin 6 = video line
Pin 12 = shielding

L’article Superb (3T) – Activate rearview camera (retrofit) est apparu en premier sur VAG Coding.

Purpose: to deactivate the worn brake pad warning light on the ODB (on-board computer), e.g. if the brake pad has no sensor or if the sensor has a problem / Brake Pad Warning light desactivation.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 0: “Brakepad warning active/installed”.

L’article Superb (3T) – Deactivate brake pad warning light est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Superb (3T) – Deactivate windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to activate voice control on the RNS 510 (SDS).

ATTENTION: RNS 510 firmware must be version v2660.

Activating voice control brings up the “Voice control” menu in the RNS 510’s SETUP menu.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “Select”, then click on “Select”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket. “37 – Navigation”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 3, check the box for“Bit 1: Microphone Diagnostics active”.

Byte 7, uncheck the box for“Bit 1: Voice Control inactive”.

To install the microphone, connect the microphone lead to the rear of the RNS 510. Connect to pins (Mic-)C1 and (Mic+)C7.

L’article Superb (3T) – Activate RNS 510 voice control est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Skoda Superb (3T)
–> Buy your OBDeleven device with VAG Custom

Skoda Superb 2 (3T) (2008-2015)

2008-2013 :

• Activate Bluetooth RNS315
• Air recirculation memory
• Audio volume down
• Manual activation of take-home
• Bending lights
• Driver’s seat heating memory
• DRL function with flashing light
• Easy entry
• Emergency brake lights
• Front parking aid volume
• Front parking aid tone
• Headlamp washer
• Heating test
• Unlocking the heater
• LED footwell lighting
• Mirror lowering
• MirrorLink on the move 1
• MirrorLink on the move 2
• Oil service reset
• Parking aid confirmation sound
• PTT button options
• Rear cover control
• Rear parking aid volume
• Rear parking aid tone
• CD lock RNS 310/315
• RNS 310/315 Image OPS developer menu
• RNS 310/315 Reversing camera
• RNS 310/315 SDS
• Test mode
• RNS 510 Image OPS
• RNS 510 SDS
• RNS 510 Speed limit
• RNS Theme 510
• Synchronized mirrors
• Automatic home fires
• Automatic locking/unlocking
• Automatic closing in case of rain
• Behavior when key is inside trunk
• Brake assist parameters
• Type of CH light activation
• CH/LH lights
• CH/LH lights via dipped beam/fog lights
• Comfort operation for sunroof sunshades
• Comfort flashing light
• Time to return home
• Correction of consumption display
• Cruise control display
• RCD 210/310 driving-school mode
• DRL as position light
• Daytime running light dimming
• Daytime running light settings
• DRL with ADL
• DRL OFF with handbrake
• Folding mirrors
• Attenuation of floor lighting with door open
• Floor lighting while driving
• Front fog lights in reverse
• Gauge test – Needle sweep
• Headlamp washer activation delay
• Freeway lights
• Hill-start assist
• Hill-start assist release parameters
• Home departure time
• Acoustic confirmation of locking/unlocking
• Optical parking system
• Activate parking assistance Tone
• Parking aid audio volume reduction
• Permanent position lights
• Rain lights
• Back drop wiping
• Rear wiper with front wiper (interval)
• Rear wiper with front wiper (permanent)
• Rear wiper with reverse
• Fuel quantity in instrument panel
• Seat belt warning
• Tailgate sound
• Droplet wiping
• XDS activation
• XDS parameters
• Engine oil type
• Keyless entry deactivation
• Oil drain distance
• Oil change interval

2013-2015 :

• Easy entry
• Folding mirrors
• Gauge test – Needle sweep
• Inspection service reset
• Oil service reset
• Rear cover control
• CD lock RNS 310/315
• RNS 310/315 developer menu
• Image OPS RNS 310/315
• RNS 310/315 reversing camera
• SDS RNS 310/315
• Test mode
• Image OPS RNS 510
• SDS RNS 510
• Speed limit RNS 510
• RNS 510 theme
• Automatic home fires
• Automatic locking/unlocking
• Automatic wiper in reverse
• Automatic closing in case of rain
• Behavior when key is inside trunk
• Brake assist parameters
• Central locking with IGN
• Type of CH light activation
• CH/LH lights
• CH/LH lights via dipped/fog lights
• Comfort operation for sunroof sunshades
• Comfort flashing light
• Time to return home
• Correction of consumption display
• Bending lights
• Bending lights with reverse
• Cruise control display
• RCD 210/310 driving-school mode
• DRL as position light
• Daytime running light dimming
• DRL in the MFD+
• Daytime running light indicator in instrument panel
• DRL OFF with handbrake ON
• Daytime running light settings
• DRL with ADL
• Dynamic steering force
• Emergency brake flashing with trailer
• Emergency brake lights
• Fog lamps with high beam
• Attenuation of floor lighting with door open
• Floor lighting
• Floor lighting while driving
• Headlamp washer
• Headlamp washer activation delay
• Freeway lights
• Hill-start assist
• Hill-start assist release parameters
• Instrument cluster language
• Instrument cluster region
• Departure time
• LED license plate lamps
• Acoustic confirmation of locking/unlocking
• Mirror lowering
• Optical parking system
• Parking aid activation tone
• Parking aid audio volume reduction
• Permanent position lights
• Rain lights
• Rear parking aid volume
• Rear parking aid tone
• Rear window wiper
• Rear wiper with front wiper (interval)
• Rear wiper with front wiper (permanent)
• Fuel quantity in instrument panel
• Remote window function
• Seat belt warning
• Disabling the Start/Stop system
• Synchronized mirror adjustment
• Tailgate sound
• Teardrop wipe
• Tire pressure warning
• Washer fluid indicator
• Windshield wiper control
• XDS activation
• XDS parameters
• Motor fan test
• Engine oil type
• Unlocking the heater
• Inspection service distance
• Inspection service interval
• Multimedia restart
• Multimedia security notice
• Oil change service distance
• Oil change service interval
• Service warning coming soon

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps SUPERB (3T) list est apparu en premier sur VAG Coding.

Purpose: to deactivate the daytime running lights (DRL) when the handbrake is engaged.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 11:
Bit 0: If this is a hidden bit, replace the last 0 to the right of Binary with 1.(10001000 => 10001001)

L’article Superb (3T) – Daytime running light deactivation (DRL) with handbrake on est apparu en premier sur VAG Coding.

Purpose: Disables license plate light control. Useful when installing LED bulbs without resistance or for error prevention.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 23:

Bit 6: Uncheck: “Lamp Monitoring (Cold) License Plate Lamps Active”.

L’article Superb (3T) – Disable plate lighting control (ODB LED error) est apparu en premier sur VAG Coding.

Purpose: to add DRL activation/deactivation to the ODB (MFA). (2011+)

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1 :

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 15: Bit 7: Check “Daytime Running Light (DRL) Active adaptation (MFA+)”.

L’article Superb (3T) – Add daytime running lights (DRL) to ODB est apparu en premier sur VAG Coding.

Purpose: to activate daytime running lights (DRL) only when the light switch is in Auto position.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 26:
Bit 3: Check “Daytime Running Light (DRL) only active with Assistance Driving Light (ADL) active”.

L’article Superb (3T) – Activate daytime running lights (DRL) only with headlight switch in Auto position est apparu en premier sur VAG Coding.