Purpose: to correct the fuel consumption display on the Trip Computer/Virtual Cockpit.

Note: these changes affect the display of instantaneous consumption, average consumption and fuel quantity.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition, then run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

4 – Click on“Adaptation- 10”.

5 – Select Channel: “Display correction of consumptions and operating range”.

Adjust consumption correction factor between 85% and 115%. (base value: 100)

Example 1: Calculation based on volume per distance (e.g. l/100 km): DIS: 9.3 l/100 km. Actual: 9.8 l/100 km. (100, 9,8 / 9,73 ? 105,38) Channel 3 will be changed from 100 to 105.
Example 2: Calculation based on volume distance (e.g. MPG is: DIS: 23 MPG. Actual: 24 MPG. (100, 23/24 and 95.83) Channel 3 will be changed from 100 to 96.

Example 3: the consumption announced by the ODB is 5.9l/100km, after checking it is actually 6.3l/100km.
Calculation of the rate to be entered: (6.3 * 100) / 5.9 = 106.78. The rate used will be 107%, and the consumption announced by the ODB will be a pessimistic 0.1l/100km.

Consumption is immediately modified on the MMI.

L’article Scala (NW) – Correction of ODB consumption display est apparu en premier sur VAG Coding.

Purpose: to adjust the hardness of the power steering for a softer steering wheel (Comfort) or a harder sporty one (Dynamic).
Warning: if you have the driving mode selection, do not modify!

Procedure :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program. Procedure: 1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

Line 1:

3 – Click on“Select”, then click on“44 – Steering Assistance”.

4 – Click on“Security Access – 16” then enter the code“19249”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Courbes caractéristiques d’assistance de direction” /“Characteristic curve of steering assistance”

7 – On this same page, there is a second drop-down menu but towards the bottom
of the page.
On this, choose the value:“Confort” or “Dynamic” then validate.

selection_by_charisma: You have the driving modes, do not modify this value otherwise you will lose the hardness of the steering wheel according to your driving mode!

L’article Scala (NW) – Modify power steering hardness est apparu en premier sur VAG Coding.

Purpose: to set the mirror folding option via remote control when locking the vehicle.


The vehicle must be equipped with the “Electrically folding mirrors” option !



Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.


Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Access Control 2-Funk Spiegelanklappung Modus”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, choose the value you require and confirm.

• Default: “by convenience operation via remote control key” = long press on key button to fold outside mirrors.
• Alternative: “by look command via remote control key” = briefly press the key button to fold the outside mirrors.

L’article Scala (NW) – Mirror folding adjustment by remote control est apparu en premier sur VAG Coding.

Purpose: to adjust the intensity of the hands-free system’s microphone.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Microphone sensitivity” or “Mikrofonempfindlichtkeit”.

7 – On this same page, there is a second drop-down menu at the bottom of the page.
On this menu, choose a value expressed in“dB” (default value“0 dB”) then validate.

L’article Scala (NW) – Microphone sensitivity adjustment est apparu en premier sur VAG Coding.

Purpose: To deactivate / remove MirrorLink from SmartLink on the MIB. The Mirrorlink service is no longer available since June 1, 2020 on Android natively. For direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Scala (NW) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: to display oil temperature on the ODB/Virtual Cockpit.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“17 – Instruments”.

4 – Click on“Coding – 07” then click on“Long Coding Helper” .

5 – Select byte“10”
Then check Bit“1”:“Display Oil Temperature”.

L’article Scala (NW) – Oil temperature on ODB est apparu en premier sur VAG Coding.

Purpose: to display fan speed when automatic air-conditioning mode is activated. (Climatronic fan speed display Auto mode)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“11”
Then select Bit“0-1”:“Blower display in Auto mode, enabled”.

L’article Scala (NW) – Display of fan speed on air conditioning in Auto mode est apparu en premier sur VAG Coding.

Purpose: to deactivate the beep when reverse gear is engaged or when parking assistance is activated manually.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “10 – Assistance stationnt”.

4 – Click on“Security Access – 16” then enter the code“71679”.

5 – Click on “Adaptation – 10”.

6 – Select “Tonalité d’activation de l’aide au stationnement ” / “Park assist activation tone ” / “Aktivierungston für Einparkhilfe ” from value list

7 – Select “Off” in the second value list

L’article Scala (NW) – Deactivation of parking aid activation beep est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for the Skoda Scala (NW)
–> Buy your OBDeleven device with VAG Custom

Skoda Scala NW (2019+ )

• Interior lights with progressive extinction/extinction
• Adaptive lane guidance
• Burglar alarm system
• Auto CH/LH
• CH/LH car lights
• Automatically folding mirrors
• Automatic exit lock
• Automatic unlocking after P
• Basic transmission settings
• Brake control when using ACC
• Bulb diagnostics: high beam
• Central locking with IGN
• Comfort turn signals
• Correction of consumption display
• Turn signal dimming rate
• Activating cruise control
• MIB2 driving-school mode
• High beam on/off
• High beam settings in main unit
• DRL with fog lights
• DRL disabled with handbrake
• Fan level display in AUTO mode
• High beam off in reverse
• High beam with turn signal
• Front high beam in reverse
• Gauge test – Needle sweep
• Headlamp washer
• Heated seat memory
• High beam assistance
• High beam assistance (MY2021 onwards)
• High beam assistance (up to MY2020)
• High beam memory
• Hill start assist Settings
• Inspection service reset
• Lane assist parameters memory
• Stopwatch
• LED license plate illumination
• Acoustic confirmation of locking/unlocking
• Turn signal mirrors with CH/LH
• All-terrain information display
• Oil service reset
• Open door alarm
• Power steering activation
• Start button pulse
• Rear teardrop wiper
• Fuel quantity in instrument panel
• Scandinavian daytime running lights
• Seat belt warning
• Speed-dependent wipers
• Static bend lights
• Static bend light parameters
• Tail lights on when tailgate open
• Rear lights when trunk is open
• Tailgate sound
• Third brake light when trunk is open
• TPMS in the dashboard
• Turn signals when trunk is open
• Turn signals Turn signals with tail lights
• American-style turn signals
• MIB3 motion video enabled
• RS virtual cockpit layout
• Closing windows after locking
• Window functions from remote control
• ACC speed gas pedal
• Radio AM
• Automatic home fires
• Automatic headlight settings
• Automatic locking/unlocking
• Automatic unlocking with ignition
• Battery capacity
• Battery type
• Brake light test
• Stop lights when trunk is open
• Brake pad warning
• CarPlay Wireless MIB3
• Type of CH light activation
• CH/LH light variant
• Comfort operation for sunroof
• Comfort windows menu
• Time to return home
• Compass position on dashboard
• Door lock test
• Driver information system (DIS) display
• DRL activated with AUTO
• DRL activated with parking lights
• Motor fan test
• Engine oil type
• Fog lights with door open
• Left front door lock test
• Pace-Car “Urban Joke” front turn signals
• Right front door lock test
• Fuel system priming
• Emergency switch brightness
• Headlight notification
• Headlamp washer test
• Road lights without IGN
• Turn signals with comfort windows
• Inspection service distance
• Inspection service interval
• Track assistance
• V2 track assistance setting memory
• Home departure time
• License plate lights with DRL
• License plate lights with trunk open
• Low ambient temperature warning
• Multimedia restart
• Oil drain distance
• Oil change interval
• Urban Joke” control car indicators
• Parking aid audio volume reduction
• Parking aid deactivation speed
• Parking lights on both sides
• Left rear door lock test
• Right rear door lock test
• Automatic rear wiper activation
• Back-up light test
• Warning of impending maintenance
• Management response
• Rear lights with door open
• Turn signal test
• Turn signal flashing mode
• Turn signals with door open
• Turn signals with CH/LH
• American-style turn signals with DRL

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article OBDeleven One-Click Apps list SCALA (NW) est apparu en premier sur VAG Coding.

Purpose: turns interior lights (door knobs, dashboard, center console) on and off gradually. By default, interior lights are switched on and off immediately with the headlights. Activating this function will cause a slow fade effect each time the interior lights are switched on or off. (Interior Light Fade in/out)

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Interior lighting-KL58 Einschalten mit Rampe”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

OBDeleven:

L’article Scala (NW) – Activation of progressive interior lighting est apparu en premier sur VAG Coding.