Purpose: Allows you to add Apple CarPlay and Android Auto to SmartLink after it has been enabled on MIB2 systems with part numbers starting with 2xxT, when only MirrorLink appears in the SmartLink menu.

For the firmware reference:
MST2_EU_SK_ZR_P02XXT

–> SmartLink Activation for CarPlay and Android Auto
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Octavia 3 (5E) – Add CarPlay / Android Auto after activating SmartLink MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Displays the “Driving Mode” on the Amundsen Bolero Columbus MIB2. This may need to be enabled after replacing the MIB if the driving modes are no longer available.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma_over_threshold_high“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17_msg_bus“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Infotainment data bus” and then confirm.

L’article Octavia 3 (5E) – Driving Mode on MIB2 est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
This is convenient for instantly viewing the active profile without having to go through the multimedia menu.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Octavia 3 (5E) – Driving Mode on OBD est apparu en premier sur VAG Coding.

Purpose: to code and adapt the Touch Climatronic panel so that the AC climate control/compressor is functional after installation. (Touch Climatronic) (Retrofit)

Touch Climatronic Unit ref example: 3G8907044 / 5NA907044AJ

Tactile climate control coding

Procedure:
1– Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2– Switch on the ignition and run the VCDS program.

The coding information is found using the “Long Coding Helper” when connecting to the vehicle with VCDS. Before replacing a module, save the original coding of the original A/C module and transfer it to the new touchscreen A/C module.

Transfer old unit’s long code to new unit’s long code + Check

3 – Click on“Select” then click on“08 – Climatronic” / “08 – Auto HVAC“.

4 – Click on“Coding- 07” then click on“Long Coding Helper“.

5 – Copy the long code (1) (the 30 or so digits in yellow) (on a notepad on your PC, for example) from your original air-conditioning system, then exit VCDS and change your current air-conditioning panel to touch-sensitive, relaunch VCDS and paste the saved long code in place of the current touch-sensitive air-conditioning long code! then exit -> Go

Options :

Coding : Only if you don’t have a rear-row climate control unit, e.g. Golf 7.5 (VCDS with experimental menu only)

3 – Click on“Select” then click on“08 – Climatronic” / “08 – Auto HVAC“.

4 – Click on“Coding- 07” then click on“Long Coding Helper“.

5 – Select byte“7“
Then check Bit“2-3” [LN]_Climate zones second row of seats : [VN]_not installed : Enabled

Adaptation (option)

3 – Click on“Select” then click on“08 – Climatronic” /“08 – Auto HVAC“.

4 – Click on “Adaptation – 10”.

5 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“ENG248446-HMI_View_Switch“.

6 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Basic setting for air-conditioning compressor

Note: the basic setting must be made when the air-conditioning control module (J301) or the damper motor(s) have been replaced.

Adaptation of shutter end stops
Required when shutter motors are replaced or when a self-check is required for self-diagnosis of defective motors.

[Select]
[08 – Climatronic” / “08 – Auto HVAC]
[Basic settings – 04]
Select IDE01546-ENG167462 “Adapt shutter/door end stops” from the drop-down list
[Go!]
Basic setting takes about 20 seconds.
Completed correctly should be displayed
[Stop]
[Completed, Go back]
[Close controller, Go back – 06]
Clear fault codes !!!

Initial running-in of air-conditioning compressor
Required when air-conditioning control module (J301) is replaced.

Prerequisites for starting the first running-in of the air-conditioning compressor in basic mode :

• Engine idling
• Transmission in Park or Neutral position
• Do not switch off the ignition
• The basic setting has been made for the shutters
• Interior fan motor is on
• Air vents fully open
• Load management not active

Steps for the “first running-in of the air-conditioning compressor” :

1- Start the engine and let it idle.

2- Go to adaptation and change the values of these two channels to 120 s :

[Select]
[08 – Climatronic” / “08 – Auto HVAC]
[Adaptation – 10]

IDE01503-Basic setting operating time for compressor running-in, 120 s, 1 … 120 you must carry out the process/modification even if it already has the value of 120 s.
IDE03176-Compressor runtime, 60 s, 1 … 120

3- Close/quit controller/unit 08, Close/quit VCDS, Switch off motor, Wait between 30 seconds and one minute, Restart motor, Open VCDS again and re-enter unit 08, Go to adaptation and re-enter original values, 120 and 60 respectively.

4- Go to basic settings.

[08 – Climatronic” / “08 – Auto HVAC]
[Basic settings – 04]

Select IDE02259-ENG167462 “Compressor run/rod in: automatic start” from the drop-down list.
[Go!]
Wait 120 s (2 min), observe the A/C button indicator on the clim touch panel flashing.
Once the basic settings have been completed, the A/C indicator goes out and the process is finished.
[Stop]

Check fault codes. Delete if necessary. Exit Climatronic 08. Check that A/C button is working/on.

Basic setting Without VCDS :

Switch on the motor, then press AC+MENU simultaneously for 10 seconds. Please wait 2 to 3 minutes (correspondence is in progress at this time) and do not perform any irrelevant actions!
Once the process is complete, the air purification and internal circulation LEDs will work! If this does not work, please check the code and whether the motor is switched on!

Then press and hold rear window defroster + AC for 2 to 3 minutes (it will fail if you move away for a second). Be patient and try several times. If you see the AC light on, you’ve succeeded.

If the MENU button doesn’t display anything on your Discover screen :

Line 1:

3 – Click on“Select” then click on“5F – Electr. information“.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-climatic_master_0x01” and“climatic_slave_0x02” and“auxilary_heating_0x03“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 10:

3 – Click on“Select” then click on“5F – Electr. information“.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6- On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Car_Function_List_BAP_Gen2-climatic_master_0x01_msg_bus” and“climatic_slave_0x02_msg_bus” and“auxilary_heating_0x03_msg_bus“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“data Extended” and confirm.

L’article Octavia 3 (5E) – Activate Touch Climatronic (retrofit) est apparu en premier sur VAG Coding.

Purpose: to activate fog lamps when reversing.

Watch out! There are 4 lines of coding to do here.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12NL LB45-Lichtfunktion C 12“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Rueckfahrlicht” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte12NL LB45-DimmwertCD12“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“100” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13NL RB5-Lichtfunktion C 13“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“Rueckfahrlicht” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte13NL RB5-DimmwertCD13“.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“100” and confirm.

D12 and D13 if C12 and C13 are already active, 127 instead of 100 if you have LED ABs.

L’article Octavia 3 (5E) – Activating fog lamps when reversing est apparu en premier sur VAG Coding.

Purpose: activates rearview mirror defrosting automatically when rear window defrosting is activated, to avoid having to move the rearview mirror switch to set defrosting, for example when in position R for reversing.


Warning! There are 2 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“52 – Passenger door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“: “Rear window heater trigger, active“


Line 2:

3 – Click on“Select”, then click on“42 – Driver’s door”.

4 – Click on“Coding – 07” then click on“Long Coding Helper”.

5 – Select byte“9“
Then uncheck Bit“2“:“Rear window heater trigger, active“.

L’article Octavia 3 (5E) – Activate automatic mirror defrosting with rear window est apparu en premier sur VAG Coding.

Purpose: activates the parking lights on both sides of the vehicle, instead of the default single-side activation via the turn signal switch. Practical for improving night-time visibility when the vehicle is parked on the side of the road.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose “Außenlicht_uebergreifend-Parklicht ueber LSS aktiviert”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select “Bilateral” and confirm.

L’article Octavia 3 (5E) – Activate parking lights on both sides est apparu en premier sur VAG Coding.

Purpose: enables headlight flashes to be made even when the ignition is off.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Driving light and parking light-Lichthupe bei Zuendung aus moeglich”.

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

L’article Octavia 3 (5E) – Contactless headlight activation est apparu en premier sur VAG Coding.

Goal: Add fog lamps for Coming Home and Leaving Home in addition to LEDs and Xenon.

Warning! There are 5 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to
the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Comfort illumination-Coming Home Leuchten”.

7 – On the same page, there’s a second drop-down menu at the bottom
of the page.
Select“Low Beam” and confirm.

Line 2:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on “Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 12NL LB45-Lichtfunktion E 12”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Coming Home oder Leaving home Aktiv” and confirm.

Line 3:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 12NL LB45-Dimmwert EF 12”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“100” and confirm.

Line 4:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 13NL RB5-Lichtfunktion E 13”.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Coming Home oder Leaving home Aktiv” and confirm.

Line 5:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Security Access – 16” then enter the code“31347”.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Leuchte 13NL RB5-Dimmwert EF 13”.

7 – On this same page, there is a second drop-down menu, but at the bottom
of the page.
On this menu, select“100” and confirm.

L’article Octavia 3 (5E) – Coming / Leaving Home with fog lamps, Xenon and LEDs est apparu en premier sur VAG Coding.

Purpose: activates the distance control on the screen menu, to adjust Front Assist parameters.

Information: This setting is only possible if the HW part number of the control unit for remote control with 2Q0 or 3Q0 starts.
Older control units starting with 5Q0 (usually with 7-byte coding) do not offer this option.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostic socket or OBDeleven box.

2 – Switch on the ignition and run the VCDS program or the OBDeleven application.

Line 1:

3 – Click on“Select” then click on “.13 – Auto Dist. Reg“.

4 – Click on“Coding – 07” then“Long Coding Helper”.

5 – Select byte“11”
Then uncheck Bit“3”:“adjustability_awv_pre_warning”.

OBDeleven: Select “adjustability_awv_pre_warning”
Change from “activated” to “Deactivated”.

Bit 3 set: On/off warning :

Bit 3 unchecked: Warning “early/mid/late/deactivated” :

L’article Octavia 3 (5E) Facelift – Front Assist settings est apparu en premier sur VAG Coding.