Purpose: Allows you to disable or remove MirrorLink from SmartLink on the MIB2 PQ. The MirrorLink service has not been natively available on Android since June 1, 2020. For a direct connection to Android Auto.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Vehicle configuration-Mirror_link“.

7 – On the same page, you’ll find a second drop-down menu at the bottom
of the page.
On this menu, select“Disabled” and confirm.

L’article Yeti (5L) – Deactivate MirrorLink est apparu en premier sur VAG Coding.

Purpose: Allows you to add Apple CarPlay and Android Auto to SmartLink after it has been enabled on MIB2 systems with part numbers starting with 2xxT, when only MirrorLink appears in the SmartLink menu.

For the firmware reference:
MST2_EU_SK_PQ_P02XXT

–> SmartLink Activation for CarPlay and Android Auto
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Yeti (5L) – Add CarPlay / Android Auto after activating SmartLink MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Allows you to add Apple CarPlay and Android Auto to SmartLink after it has been enabled on MIB2 systems with part numbers starting with 2xxT, when only MirrorLink appears in the SmartLink menu.

For the firmware reference:
MST2_EU_SK_ZR_P02XXT

–> SmartLink Activation for CarPlay and Android Auto
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Fabia (NJ) – Add CarPlay / Android Auto after activating SmartLink MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Allows you to add Apple CarPlay and Android Auto to SmartLink after it has been enabled on MIB2 systems with part numbers starting with 2xxT, when only MirrorLink appears in the SmartLink menu.

For the firmware reference:
MST2_EU_SK_ZR_P02XXT

–> SmartLink Activation for CarPlay and Android Auto
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Superb (3V) – Add CarPlay / Android Auto after activating SmartLink MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Allows you to add Apple CarPlay and Android Auto to SmartLink after it has been enabled on MIB2 systems with part numbers starting with 2xxT, when only MirrorLink appears in the SmartLink menu.

For the firmware reference:
MST2_EU_SK_ZR_P02XXT

–> SmartLink Activation for CarPlay and Android Auto
–> Disable MirrorLink
–> Enable the USB port for iPhone CarPlay (retrofit)


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Apple_DIO“

7 – On this same page, there is a second drop-down menu located toward the bottom
.
From this menu, select “Enabled” and then confirm.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103“.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Vehicle Configuration – Google_GAL.”

7 – On this same page, there is a second drop-down menu further down
.
From this menu, select “Enabled” and then confirm.

L’article Octavia 3 (5E) – Add CarPlay / Android Auto after activating SmartLink MIB2 2xxT est apparu en premier sur VAG Coding.

Purpose: Displays the “Driving Mode” on the Amundsen Bolero Columbus MIB2. This may need to be enabled after replacing the MIB if the driving modes are no longer available.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma_over_threshold_high“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17_msg_bus“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Infotainment data bus” and then confirm.

L’article Kodiaq (NS) – Driving Mode on MIB2 est apparu en premier sur VAG Coding.

Purpose: Displays the “Driving Mode” on the Amundsen Bolero Columbus MIB2. This may need to be enabled after replacing the MIB if the driving modes are no longer available.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma_over_threshold_high“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17_msg_bus“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Infotainment data bus” and then confirm.

L’article Karoq (NU) – Driving Mode on MIB2 est apparu en premier sur VAG Coding.

Purpose: Displays the “Driving Mode” on the Amundsen Bolero Columbus MIB2. This may need to be enabled after replacing the MIB if the driving modes are no longer available.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma_over_threshold_high“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17_msg_bus“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Infotainment data bus” and then confirm.

L’article Superb (3V) – Driving Mode on MIB2 est apparu en premier sur VAG Coding.

Purpose: Displays the “Driving Mode” on the Amundsen Bolero Columbus MIB2. This may need to be enabled after replacing the MIB if the driving modes are no longer available.


Watch out! There are 4 lines of coding to do here.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 2:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_Adaptations_Gen2-menu_display_charisma_over_threshold_high“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, choose the“active” value.

Line 3:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17“

7 – On this same page, there is a second drop-down menu at the bottom
of the page.
On this menu, select“active” and confirm.

Line 4:

3 – Click on“Select” then click on“5F – Electr. information”.

4 – Click on“Security Access – 16” then enter the code“20103”.

5 – Click on“Adaptation – 10”.

6 – At the very top of this page, there is a drop-down menu.
From this drop-down menu, select “Car_Function_List_BAP_Gen2-charima_0x17_msg_bus“

7 – On this same page, there is a second drop-down menu located toward the bottom
of the page.
From this menu, select “Infotainment data bus” and then confirm.

L’article Octavia 3 (5E) – Driving Mode on MIB2 est apparu en premier sur VAG Coding.

Purpose: Displays the selected driving mode (Eco, Normal, Sport, Individual, etc.) directly on the on-board computer (ODB) or Virtual Cockpit.
This is convenient for instantly viewing the active profile without having to go through the multimedia menu.


Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “19 – CAN Gateway.”

4 – Click on“Coding – 07” then on“Long Coding Helper” .

5 – Select byte “8“
. Then check bit “4” (Display for Drive Program Functions in Instrument Cluster active).

L’article Karoq (NU) – Driving Mode on OBD est apparu en premier sur VAG Coding.