Purpose: Resets the settings for all remote controls associated with the vehicle.

WARNING: After completing this procedure, all remote controls will be deleted and will need to be reprogrammed using the “Program a Remote Control” tutorial .
If your vehicle is equipped with a KESSY remote control (05 – Access/Start Authorization), you cannot delete the remote controls using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 00

Set the value to 0 and save

L’article Ibiza (6J) – Resetting the remote controls est apparu en premier sur VAG Coding.

Purpose: Allows you to program the remote controls that will be used with the vehicle for central locking and unlocking.

WARNING: This procedure does not allow you to program remote controls with the vehicle’s immobilizer.
If your vehicle is equipped with a KESSY remote control (05 – Access/Ignition Authorization), you cannot program a new remote control using this procedure.

Proceed :
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click “Select,” then click “ “09 – Cent. Elect.”.”

4 – Click on “Adaptation – 10”.

5 – Select Channel 01 ( “Remote Control Adaptation” from the drop-down list)

Enter the number of keys to program, then click Save.
Next, press the Unlock button on each remote control to be programmed for at least 1 second. The flashing lights will confirm the process.
All keys must be programmed in a single session, one after the other.
Programming all keys must not take longer than 15 seconds.
You can add up to 7 remote controls. If the [Test] and/or [Save] buttons are grayed out and unclickable, the module likely has all 7 slots filled; delete the remote controls using the “Reset Remote Controls” tutorial.

L’article Ibiza (6J) – Programming a Remote Control est apparu en premier sur VAG Coding.

Purpose: to deactivate the windshield washer indicator on the ODB (on-board computer).

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 2: “Washer Fluid warning active/installed”.

L’article Ibiza (6J) – Deactivating the windshield washer indicator est apparu en premier sur VAG Coding.

Purpose: to activate the electronic differential lock (XDS).

The electronic differential lock (XDS) is an extension of the well-known EDS function. However, XDS does not react to acceleration slip, but rather relieves pressure on the inside front wheel when cornering. XDS applies pressure to the inside wheel during cornering from the hydraulic ESP to prevent slippage.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “03 – ABS”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

Byte 17 :
Bit 3: Tick “(Extended) Electronic Differential Lock (XDS – PR-UG3/UG4) active/installed”

Line 2 XDS setting.

3 – Click on “Select”, then click on “03 – ABS”.

4 – Click on “Adaptation – 10 ”.

Channel 36 (Electronic Differential Lock (XDS) in drop-down list)

Choose a value
0“medium”
1 “low”
2 “high

L’article Ibiza (6J) Facelift – Electronic differential lock (XDS) est apparu en premier sur VAG Coding.

OBDeleven OBD11 ONE-CLICK APPS coding and modification options for Seat Ibiza (6J)
–> Buy your OBDeleven device with VAG Custom

Seat Ibiza 4 (6J) (2008-2015) / Seat Ibiza FR / Cupra / Ibiza 6J Facelift (specific facelift coding at the bottom of the page)

• Acoustic lock confirmation
• Automatic locking/unlocking
• Central locking with IGN
• Central locking settings
• CH/LH light function
• Comfort flashing light
• Time to return home
• Emergency brake lights
• Gauge test – Needle sweep
• Headlamp washer
• Inspection service reset
• Departure time
• Oil service reset
• Parking light
• Seat belt warning
• Teardrop wipe
• CH/LH lights
• Correction of consumption display
• Bending lights
• LED license plate lamps
• Phone connection tone
• Management response
• XDS activation
• ATWS country setting
• Automatic tailgate lock
• Comfort windows
• Clutch message display
• DRL activation/deactivation
• Engine oil type
• Fog lamps with high beam
• Front wiper operating mode
• Fuel system priming
• Heated mirrors
• Hill-start assist
• Tilt sensor sensitivity
• Turn signals with comfort windows
• Inspection service distance
• Inspection service interval
• Instrument cluster language
• Inside surveillance
• Sensitivity of interior surveillance
• Acoustic lock/unlock Confirmation
• Acoustic confirmation of locking/unlocking V2
• Mirror heating with rear window
• Multifunction display
• Oil drain distance
• Oil change interval
• Rear wiper with reverse
• Remote trunk release
• Scandinavian daytime running lights
• Selective central locking
• Visual confirmation

Seat Ibiza 4 (6J) Facelift (2012-2015)

• Acoustic lock confirmation
• Automatic locking/unlocking
• Central locking with IGN
• Central locking settings
• CH/LH light function
• Comfort flashing light
• Time to return home
• Emergency brake lights
• Gauge test – Needle sweep
• Headlamp washer
• Inspection service reset
• Departure time
• Oil service reset
• Parking light
• Seat belt warning
• Teardrop wipe
• CH/LH lights
• Correction of consumption display
• Bending lights
• Fuel system priming
• LED license plate lamps
• Phone connection tone
• Management response
• ATWS country setting
• Automatic tailgate lock
• Comfort windows
• Clutch message display
• Daytime running lights on/off
• Motor fan test
• Engine oil type
• Fog lamps with high beam
• Maintenance of front wipers
• Heated mirrors
• Hill-hold assist
• Hill-start assist settings
• V2 hill start assist settings
• Tilt sensor sensitivity
• Turn signals with comfort windows
• Inspection service distance
• Inspection service interval
• Instrument cluster language
• Interior Surveillance
• Sensitivity of interior surveillance
• Acoustic confirmation of locking/unlocking
• Acoustic confirmation of locking/unlocking V2
• Mirror heating with rear window
• Multifunction display
• Oil drain distance
• Oil change interval
• Rear wiper with reverse
• Remote trunk release
• Scandinavian daytime running lights
• Selective central locking
• Warning of impending maintenance
• Visual confirmation
• XDS interaction
• Interaction XDS V2

Source: exhaustive list provided by OBDeleven for VAG Coding

L’article List OBDeleven One-Click Apps IBIZA (6J) est apparu en premier sur VAG Coding.

Purpose: Allows you to add a driving-school mode view to the SE 250 that displays speed (also ideal for accompanied driving)


Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“56 – Radio”.

4 – Click on“Adaptation – 10”.

6 – On this page, at the very top, there is a drop-down menu.
In this drop-down menu, choose“Channel 2” “Driving School Function”.

7 – Set value to 1.

L’article Ibiza (6J) – Display speed on SE 250 est apparu en premier sur VAG Coding.

Purpose: To suppress the audible alarm and the warning light on the speedometer when driving without a seatbelt.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on “Select”, then click on “17 – Instruments”.

4 – Click on “Coding – 07” then click on “Long Coding Helper” .

5 – Select byte 1:
Then uncheck Bit 1: “Seatbelt warning active/installed”.

L’article Ibiza (6J) – Delete belt alarm est apparu en premier sur VAG Coding.

Purpose: to set automatic door locking from 15km/h.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 0:
Bit 4: Check “Auto-Lock (Automatic Locking above 15 km/h)”.

L’article Ibiza (6J) – Automatic door locking est apparu en premier sur VAG Coding.

Purpose: Allows you to configure selective door unlocking.

When unlocking the vehicle, only the driver’s door is unlocked. To unlock all doors, press the remote control’s unlock button twice.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 0:
Bit 0: Check “Selective Central Locking (Single Door Locking) active”

L’article Ibiza (6J) – Selective door unlocking est apparu en premier sur VAG Coding.

Purpose: to configure automatic door unlocking when the ignition key is removed.

Procedure:
1 – Engine off, ignition off, connect your official VAG-COM VCDS cable to the computer, then plug the other end into your vehicle’s diagnostics socket.

2 – Switch on the ignition and run the VCDS program.

Line 1:

3 – Click on“Select”, then click on“09 – Cent. Elect.”.

4 – Click on“Coding 07”.

5 – Select the “0” module and click on “Long Coding Helper”:

Byte 0:
Bit 3: Check “Auto-Unlock (Unlocking when Removing the Ignition Key)”.

L’article Ibiza (6J) – Automatic door unlocking est apparu en premier sur VAG Coding.